Poulan Pro PR8527ES 421469 Snow Blower Owners Manual

OPERATION
TO ADJUST SKID PLATES (See Fig. 17)
NOTE: The  wrench provided  in your  parts bag may  be
used to adjust the skid plates.
WARNING:  Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
ground surface. Adjust skid plates evenly to proper height
for  current surface  conditions.  For removal  of  snow  in
normal conditions, such as a paved driveway or sidewalk,
place skid  plates in the highest  position (lowest scraper
clearance) to give a  1/8" clearance between the scraper
bar and the ground.  Use a  middle position if the surface
to be cleared is uneven.
CAUTION: Alcohol blended fuels (called gaso-
hol or using ethanol  or methanol) can attract
moisture which leads to separation and forma-
tion of acids  during storage.   Acidic gas can
damage the fuel system of an engine while in
storage.   To avoid  engine problems, the  fuel
system should  be emptied before  storage of
30
days or longer.   Empty the  gas tank, start
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
the  engine and  let it  run  until the  fuel lines
and carburetor are empty.  Use fresh fuel next
season. SeeStorageInstructionsforadditional
information.  Never  use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
CHOKE CONTROL
THROTTLE    PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
1.
2.
Shut off engine and wait for all moving parts to stop.
Adjust  skid plates  by loosening  the  hex nuts,  then
moving skid  plate to  desired position.  Be sure both
plates are adjusted evenly. Tighten securely.
SAFETY
IGNITION
KEY
HIGH POSITION
(LOW GROUND
CLEARANCE)
AUGER
HOUSING
SCRAPER BAR
SKID PLATE
HEX
NUTS
GASOLINE
FILLER CAP
FUEL SHUT-
OFF VALVE
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 17
SCRAPER BAR (See Fig. 17)
RECOIL
STARTER
HANDLE
STARTER BUTTON
POWER CORD PLUG
The scraper bar is not adjustable, but is reversible.  After
considerable use it may become worn. When it has worn
almost to  the  edge of  the housing,  it can  be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
NOTE:  ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 22
TO START ENGINE
Be sure fuel shut-off valve is in the “OPEN” position.
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 18)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug  and is
designed to operate on 120 Volt A.C. household current.
Be  sure  your house  is  a  120  Volt A.C.  three-wire
grounded  system.   If  you  are  uncertain,  consult a
licensed electrician.
1.
2.
Check engine oil with snow thrower on level ground.
Remove oil  fill cap/dipstick and  wipe clean,  reinsert
the dipstick and  screw tight, wait for  a few seconds,
remove and read  oil level. If necessary,  add oil until
“FULL” mark on dipstick is reached. Do not overfill.
WARNING:  Do  not   use  the  electric
starter if your  house is not a 120  Volt
A.C.three-wiregroundedsystem.  Seri-
ous personal injury or damage to your
snow thrower could result.
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
ADD GASOLINE (See Fig. 18)
Fill fuel tank to bottom of tank filler neck.  Do not over-
fill. Use fresh, clean, regular unleaded gasoline with a
minimum of 87 octane.  Do not  mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
11
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2008
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 40 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website