Note: You can pull up the adjuster link and cable to
make unhooking the spring easier.
Before each session, inspect the rotor blades for wear.
When a rotor blade edge has worn down to the wear
indicator hole, have an Authorized Service Dealer
replace the rotor blades and the scraper (Figure 24).
2.
Move the Z-fitting to a higher or lower hole on the
adjuster link as needed to obtain the 1/16-inch to
1/8-inch
(2 mm to 3 mm) gap between the control
bar and the handle (Figure 21).
Note: Moving the Z-fitting higher decreases the
gap between the control bar and the handle; moving
it lower increases the gap.
3.
4.
Hook the spring to the adjuster link and slide the
spring cover over the adjuster link.
Check the adjustment; refer to Checking the Control
Cable.
Note: After extended use, the drive belt may wear
and lose its proper belt tension. If the drive belt
slips (continuously squeals) under a heavy load,
disconnect the spring from the adjustor link and
move the upper end of the spring to the hole that
is further from the pivot point in the control bar
(Figure 23). Then connect the spring to the adjustor
link and adjust the control cable.
Figure 24
1.
Wear indicator hole
Changing the Engine Oil
Service Interval: After the first 2 hours
Yearly
Run the engine a few minutes before changing the oil
to warm it. Warm oil flows better and carries more
contaminants.
1.
2.
3.
Stop the engine and wait for all moving parts to stop.
Move the snowthrower to a level surface.
Place an oil drain pan under the oil drain plug,
remove the oil drain plug, and tip the snowthrower
backward and drain the used oil in the oil drain pan
Figure 25).
Figure 23
1.
Remove the upper end of
spring from this hole
3.
4.
Pivot point
2.
Insert the upper end of
spring into this hole
Upper end of spring
Figure 25
Note: The belt may slip (squeal) in wet conditions;
to dry out the drive system, start the rotor and run
it without a load for 30 seconds.
4.
After draining the used oil, return the snowthrower
to the operating position.
Inspecting the Rotor Blades
5.
6.
Install the oil drain plug and tighten it securely.
Clean around the oil fill cap (Figure 26).
Service Interval: Yearly—Inspect the rotor blades and
have an Authorized Service Dealer
replace the rotor blades and scraper if
necessary.
12
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38571, Toro 38575, Toro CCR 6053 Quick Clear |
| Model Number | 38571, 38575 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 280000001 - 280999999 |
| Product Name | Toro CCR 6053 Quick Clear Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Power Clear, Snowthrower |
| Swath | 21 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Engine Motor Model # | OH195SA-72568G |
| Engine Motor Size | 195cc |
| Engine Motor Type | 4 Cycle |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)