Poulan P3818 Chainsaw Owners Manual

(19
mm) socket wrench. Spark pluggap
Cylinder
Cover
should be 0.025 inch (0,6 mm).
Reinstall the spark plug boot.
the   cylinder  cover   and  3
screws. Tighten securely.
Air Filter
Cover
6.
7.
Reinstall
Air Filter
Cylinder
Cover
Spark
Plug Boot
INSPECT  MUFFLER  AND   SPARK
ARRESTING SCREEN
Spark
Plug
As the unit is used, carbon deposits build up
on the muffler  and spark arresting screen,
and must be removedto avoidcreating afire
hazard or affecting engine performance.
Replacethespark  arrestingscreen ifbreaks
occur.
REPLACE FUEL FILTER
Toreplacefuelfilter,drainyour   unitby runningit
dry offuel. Removefuelcapand   its connected
retainer from tank. Pull filter from tank and re-
move from line. Replace and reassemble.
Spark
Arresting
Screen
Exhaust
Outlet
Cover
CHAIN ADJUSTMENT
SeeCHAIN TENSION in ASSEMBLY section.
CHAIN SHARPENING
WARNING:
Improper chain sharp-
Nut
ening techniques and/or depth gauge mainte-
nance will  increase the  chance of  kickback
which can result in serious injury.
Muffler
WARNING:
Wear protective gloves
CLEANING  THE  SPARK ARREST-
ING SCREEN
when handling chain. The chain is sharp and
can cut you even when it is not moving.
Conditions which indicate  the need for chain
sharpening:
Cleaning is required every  25 hours of op-
eration or annually, whichever comes first.
1.
Loosen and remove the nut from the ex-
haust outlet cover.
S  Reduction in size of wood chips. The size
ofthewoodchipwilldecreaseas    thechain
gets duller  until it  becomes  more like  a
powder  than a  chip. Note  that  dead or
rotted wood will not produce a good chip.
S  Saw cuts to one side or at an angle.
S  Saw has to be forced through the cut.
Tools required:
S  5/32 inch (4 mm) diameter round file and
file holder
S  Flat file
S  Depth gauge tool
2.
3.
Remove the exhaust oulet cover.
Removespark arrestingscreen.Handle
screen carefully to prevent damage.
Clean the spark arresting screen gently
with  a wire  brush.  Replace screen  if
breaks are found.
4.
5.
6.
Replace any broken or cracked muffler
parts.
Reinstall spark arresting screen, exhaust
outlet cover,and nut.Tighten nutsecurely.
REPLACE SPARK PLUG
The  spark plug  should  be replaced  each
year to ensure the engine starts easier and
runs better. Ignition timing is fixed and non-
adjustable.
TO SHARPEN CHAIN:
1.
Move  ON/STOP switch  to  the STOP
position.
2.
Check chain for proper tension.  Adjust
chain tension if necessary. See CHAIN
TENSION section.
NOTE:  This spark ignition system complies
with the Canadian standard ICES--002.
1.
2.
3.
4.
Loosen 3 screws on cylinder cover.
Remove the cylinder cover.
Pull off the spark plug boot.
Remove spark  plug from  cylinder and
discard.
3.
Sharpen cutters.
S
To sharpen the cutters,  position the
file holder level (90˚) so that it rests
on the  top edges  of the cutter  and
depth gauge.
NOTE:  The chain has both left and
right hand cutters.
5.
Replace with Champion RCJ--7Y spark
plug and tighten securely with a 3/ inch
4
16
Product Specification
CategoriesChainsaw Manuals, Poulan Chainsaw Manuals
Tags
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 21 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website