Poulan Pro PP291E30 435555 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
IMPELLER SHEAR BOLTS
WARNING:  To  avoid  serious   injury,  before
performing any service or adjustments:
The impeller is secured  to the impeller shaft with two  (2)
capscrew/shearboltsandhexnuts.Shouldaforeignobject
or ice become  lodged in the impeller, the  capscrews are
designed to break, preventing damage to any other com-
ponents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear bolts:
1.
Be sure the on/off switch is in the
OFF position.
2.
3.
Remove safety ignition key.
Make sure the augers and all moving
parts have completely stopped.
1.
Disengage all  controls  and move  throttle control  to
STOP position. Wait for all moving parts to stop.
4.
Disconnect  spark  plug   wire  from
spark plug  and place wire  where it
cannot come in contact with plug.
2.
Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
SNOW THROWER
3.   Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and  “SCRAPER BAR”
in the Operation section of this manual.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts  as supplied
with your snow thrower.
CHUTE DEFLECTOR
The chute deflector, attached  to the top of the  discharge
chute, is provided  to direct discharging  snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
4.   Insertsafetyignitionkeyandreconnectsparkplugwire
to spark plug.
1
/4-20
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
LOCKNUT
WARNING:  To  avoid   serious  injury,
never operate your snow thrower with
the deflector removed or damaged.
IMPELLER HUB
IMPELLER
SHAFT
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
SHEAR BOLTS (See Fig. 20)
AUGER SHEAR BOLTS
Both right and left-hand augers are  secured to the auger
shaft with a shear bolt  and hex nut. Should a foreign ob-
ject or ice  become lodged in the augers,  the shear bolts
are designed  to break, preventing  damage to  any other
components. If one or both augers do not turn when auger
control lever is engaged, check to see if one or both of the
bolts have sheared. To replace the shear bolts:
AUGER
HUB
1/4-20
LOCKNUT
AUGER HUB
FIG. 20
AUGER SHAFT
1.
Disengage all  controls  and move  throttle control  to
STOP position. Wait for all moving parts to stop.
TO REMOVE BELT COVER (See Fig. 21)
2.
Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
1.
Remove  the two  (2)  screws securing  belt  cover to
frame.
2.
Remove belt cover.
3.
4.
Align hole in auger hub with hole in auger shaft and
install a new 1/4-20 x 2" shear bolt.  Install 1/4-20
lock nut and tighten securely.
Replace belt cover by installing cover and screws and
tighten securely.
CAUTION: Do not substitute. Use only original
equipment shear bolts  as supplied with your
snow thrower.
Insertsafetyignitionkeyandreconnectsparkplugwire
to spark plug.
FRAME
BELT COVER
FIG. 21
SCREWS
16
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 40 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website