NOTE: If the engine sounds as if it is trying
to start before the 5th pull, stop pulling and
immediately proceed to the next step.
The inertia--activated chain brake is
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S
5.
Push the choke/fast idle lever in to the
S If the brake is already activated, it is
disengaged by pulling the front hand guard
back toward the front handle as far as
possible.
S Whencuttingwiththesaw,thechainbrake
must be disengaged.
HALF CHOKE position.
CHOKE/FAST IDLE LEVER
OFF
HALF
Disengaged
Engaged
FULL
6.
7.
Pull the starter rope sharply with your
right hand until the engine starts.
Allow the engine to run for approximate-
ly 30 seconds. Then, squeeze and re-
lease the throttle trigger to allow engine
to return to idle speed.
Braking function control
The chain brake must be
checked several times daily. The engine
mustberunningwhenperformingthisproce-
dure. This is theonly instancewhen thesaw
should be placed on the ground with the en-
gine running.
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
CAUTION:
STARTING A WARM ENGINE
1.
Move ON/STOP switch to the ON posi-
tion.
2.
3.
Slowly press primer bulb 6 times.
To set the fast idle, pull the choke/fast
idle lever out to the full extent (to the full
choke position); then push the lever
back in to the HALF CHOKE position.
Pull the starter rope sharply with your
right hand until the engine starts.
Squeeze and release throttle trigger to
allow engine to return to idle speed.
4.
5.
DIFFICULT STARTING (or starting a
flooded engine)
Inertia activating function control
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by pushing the choke/fast idle lever in
completely (to the OFF CHOKE position)
and then following the warm engine starting
procedure listed above. Ensure the ON/
STOP switch is in the ON position.
Startingcouldrequire pullingthe starter rope
handle many times depending on how badly
theunitisflooded.Ifenginefailstostart,refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
WARNING:
When performing the
following procedure, the engine must be
turned off.
Grip the rear handle with your right hand and
the front handle with your left hand. Hold the
chain saw approximately 14″ (35cm) abovea
stump or other wooden surface. Release your
grip on the front handle and use the weight of
thesaw toletthetipoftheguidebar fallforward
and contact the stump. Whenthe tipof thebar
hits the stump, the brake should activate.
OPERATING TIPS
S Check chain tension before first use, after
CHAIN BRAKE
1
minute of operation, and each time be-
fore you start the chain saw. See CHAIN
TENSION in the ASSEMBLY section.
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary. If the chain
jumps off the guide bar, inspect the chain
for damageddrivelinks beforereinstalling.
Burrs on drive links, which prevent them
from entering the groove of the guide bar,
can be removed with a flat file.
WARNING:
If the brake band is
worn too thin it may break when the chain
brakeistriggered.Withabrokenbrakeband,
the chain brake will not stop the chain. The
chainbrake shouldbe replacedby anautho-
rizedservicedealer ifany partis worntoless
than 0.020″ (0.5 mm) thick. Repairs on a
chain brake should be made by an autho-
rized service dealer. Take your unit to the
place of purchase if purchased from a ser-
vicing dealer, or to the nearest authorized
master service dealer.
S Keep the chain out of dirt and sand. Even a
smallamountofdirtwilldullachain,increase
the possibility of kickback, and require chain
sharpening or replacement.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
11
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro PP3516AVX, Poulan Pro PP4218AVX |
| Model Year | 2010 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)