Hook Angle
CARBURETOR ADJUSTMENT
0.025
(0.65
inch
mm)
WARNING: Thechainwillbemoving
during most of this procedure. Wear your pro-
tective equipment and observe all safety pre-
cautions. The chain must not move at idle
speed.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if
you notice any of the following conditions:
S Chain moves at idle. See IDLE SPEED--T
adjusting procedure.
S Saw will not idle. See IDLE SPEED--T ad-
justing procedure.
Rounded
Corner
Right
Too Much Hook Angle
Squared Off
Corner
Idle Speed--T
Wrong
Allow engine to idle. If the chain moves, idle is
toofast. Iftheenginestalls,idleis tooslow. Ad-
just speed until engine runs without chain
movement (idle too fast) or stalling (idle too
slow). The idle speed screw is located in the
area above the primer bulb and is labeled T.
S Turn idle screw (T) clockwise to increase
engine speed.
WARNING:
Maintain the proper
hook angle according to the manufacturer’s
specifications for the chain you are using. Im-
proper hook angle will increase the chance of
kickback which can result in serious injury.
S Turn idle screw (T) counterclockwise to
decrease engine speed.
4.
Check and lower depth gauges.
If you require further assistance or are unsure
about performing this procedure, contact your
authorized service dealer or call our customer
assistance help line at 1--800--554--6723.
Depth Gauge Tool
File
Depth Gauge
COOLING SYSTEM
To keep the working temperature as low as
possible the machine is equipped with a
cooling system.
S
S
Place gauge tool on cutter.
If the depth gauge is higher than the
depthgaugetool,fileitleveltothetopof
the depth gauge tool.
Maintain rounded front corner of
depth gauge with a flat file.
NOTE: The very top of the depth
gauge should be flat with the front
half rounded off with a flat file.
If you require further assistance or are unsure
about performing this procedure, contact your
authorized service dealer or call our customer
assistance help line at 1--800--554--6723.
The cooling system consists of:
S Air intake on the starter
S Air guide plate
S Fins on the flywheel
S Cooling fins on the cylinder
Cylinder cover (directs cold air over the
cylinder)
S
S
Clean the cooling system with a brush after
each use, more often in demanding condi-
tions. A dirty or blocked cooling system re-
sults in the machine overheating which
causes damage to the piston and cylinder.
STORAGE
S Store in a clean dry area.
S Lightly oil external metal surfaces and
guide bar.
WARNING:
Perform the following
steps after each use:
S Allow the engine to cool, and secure the
unit before storing or transporting.
S
Oil the chain and wrap it in heavy paper or
cloth.
S Store chain saw and fuel in a well venti-
lated area where fuelvapors cannotreach
sparks or openflames from water heaters,
electric motors or switches, furnaces, etc.
S Store chain saw with all guards in place
and position chain saw so that any sharp
object cannot accidentally cause injury.
S Store chain saw well out of the reach of
children.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message
labeled IMPORTANT regarding the use of
gasohol in your chain saw. Fuel stabilizer is
an acceptable alternative in minimizing the
formation of fuel gum deposits during stor-
age. Add stabilizer to the gasoline in the fuel
tank or fuelstoragecontainer.Follow themix
instructions found on stabilizer containers.
Run engine at least 5 minutes after adding
SEASONAL STORAGE
Prepareyourunitfor storageattheendofthe
season or if it will not be used for 30 days or
more. If your chain saw is to be stored for a
period of time:
stabilizer.
Poulan/WEED
EATER 40:1,
2-cycleengineoil(air cooled)is blendedwith
fuel stabilizer. If you do not use this oil, you
can add a fuel stabilizer to your fuel tank.
S Clean saw thoroughly before storage.
17
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro PP3816AV, Poulan Pro PP4218AV, Poulan Pro PP4218AVL |
| Model Year | 2010 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)