Poulan Pro PPB3416 PPB4218 Chainsaw Owners Manual

Startingcouldrequire  pullingthe starter rope
handle many times depending on how badly
theunitisflooded.Ifenginefailstostart,refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
OPERATING TIPS
S  Check chain tension before first use, after
1 minute of operation, and each time be-
fore you start the chain saw. See CHAIN
TENSION in the ASSEMBLY section.
S  Cut wood only.  Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S  Stop the saw if the chain strikes a foreign
object. Inspect the saw  and repair or re-
place  parts  as  necessary. If  the  chain
jumps off the guide bar, inspect the chain
for damageddrivelinks beforereinstalling.
Burrs on drive links,  which prevent them
from entering the groove of the guide bar,
can be removed with a flat file.
CHAIN BRAKE
WARNING: Ifthebrakebandisworn
too thin it may break when thechain brakeis
triggered.  With a  broken brake  band,  the
chainbrakewillnotstopthechain.Thechain
brake should be replaced by an authorized
service dealer if any part is wornto less than
0.020(0.5 mm)  thick. Repairs on  a chain
brake should be made by an authorized ser-
vicedealer.Takeyour  unittotheplaceofpur-
chase if purchased from a servicing dealer,
or to the nearest authorized master service
dealer.
S  Keep the chain out of dirt and sand. Even a
smallamountofdirtwilldullachain,increase
the possibility of kickback, and require chain
sharpening or replacement.
S  Practice cutting a few small logs using the
following techniques to get the“feel” ofus-
ing your  saw before  you begin  a  major
sawing operation.
S  This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S  The
inertia--activated   chain   brake   is
S
S
S
S
Squeeze the throttle trigger and allow the
engine to reach full speed before cutting.
saw  frame
activated if the front hand guard is pushed
forward,  either  manually   (by  hand)  or
automatically (by sudden movement).
S  If  the  brake  is  already  activated,  it  is
disengagedby pullingthefronthandguard
back  toward the  front handle  as  far as
possible.
Begin  cutting   with  the
against the log.
Keep the engine at full speed the entire
time you are cutting.
Allowthechaintocutforyou.Exertonly
light downward pressure.  If you force
thecut,damagetothebar,chain,oren-
gine can result.
S  Whencuttingwiththesaw,thechainbrake
must be disengaged.
Disengaged
S
Release the throttle trigger as soon as
the cut is completed,  allowing the en-
gine to idle.  If you  run the saw at full
throttlewithoutacuttingload,unneces-
sary wear can occur to the chain, bar,
and engine. It  is recommended that
the engine not be operated for lon-
ger than 30 seconds at full throttle.
To avoid losing control when cut is com-
plete, do not put pressure on saw at end
of cut.
Engaged
Braking function control
S
CAUTION:
The  chain  brake  must  be
checked  several times  daily.  The  engine
mustberunningwhenperformingthisproce-
dure. This is theonly instancewhen thesaw
should be placed on the ground with the en-
gine running.
S  Stop the  engine before  setting the  saw
down after cutting.
TREE FELLING TECHNIQUES
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the  chain brake  by turning  your  left wrist
against  the hand  guard  without releasing
your grip around the front handle. The chain
should stop immediately.
WARNING: Check forbrokenordead
branches which can fall while cutting causing
serious injury.   Do  not cut near  buildings or
electrical wires if you do not know the direction
of tree fall, nor cut at night since you will not be
aletoseewell,nor   duringbadweather  suchas
rain, snow,  or strong winds,  etc.  If  the tree
makes contact  with any utility  line, the utility
company should be notified immediately.
S  Carefullyplanyour sawingoperationinad-
vance.
Inertia activating function control
WARNING:  When  performing  the
following  procedure,  the  engine must  be
turned off.
Grip the rear handle with your right hand and
the front handle with your left hand.  Hold the
chain saw approximately 14(35cm) abovea
stump or other wooden surface. Release your
grip on the front handle and use the weight of
thesaw toletthetipoftheguidebar    fallforward
and contact the stump. Whenthe tipof thebar
hits the stump, the brake should activate.
S  Cleartheworkarea.  Youneedacleararea
allaroundthetreeso   youcan havesecure
footing.
S  The chain saw operator  should keep on
the uphill side of the terrain as the tree is
likelytorollor  slidedownhillafteritisfelled.
S  Study the natural conditions that can cause
the tree to fall in a particular direction.
Natural conditions that can cause a tree  to
fall in a particular direction include:
11
Product Specification
CategoriesChainsaw Manuals, Poulan Pro Chainsaw Manuals
Tags,
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 21 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website