Poulan Pro XT627ES 437920 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
WARNING: To avoid serious injury, before performing any service or adjustments:
1.
2.
3.
4.
Be sure the on/off switch is in the OFF position.
Remove safety ignition key.
Make sure the augers and all moving parts have completely stopped.
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact
with plug.
SNOW THROWER
2.   Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and  “SCRAPER BAR”
in the Operation section of this manual.
3.
Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
CHUTE DEFLECTOR
The chute deflector, attached  to the top of the  discharge
chute, is provided  to direct discharging  snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts  as supplied
with your snow thrower.
WARNING:  To  avoid   serious  injury,
never operate your snow thrower with
the deflector removed or damaged.
4.   Insertsafetyignitionkeyandreconnectsparkplugwire
to spark plug.
1
/4-20
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
LOCKNUT
IMPELLER HUB
SHEAR BOLTS (See Fig. 18)
AUGER SHEAR BOLTS
IMPELLER
SHAFT
Both right and left-hand augers are  secured to the auger
shaft with a shear bolt  and hex nut. Should a foreign ob-
ject or ice  become lodged in the augers,  the shear bolts
are designed  to break, preventing  damage to  any other
components. If one or both augers do not turn when auger
control lever is engaged, check to see if one or both of the
bolts have sheared. To replace the shear bolts:
AUGER
HUB
1.
Disengage all  controls  and move  throttle control  to
STOP position. Wait for all moving parts to stop.
2.
Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
Align hole in auger hub with hole in auger shaft and
install a new 1/4-20 x 2" shear bolt.  Install 1/4-20
lock nut and tighten securely.
1/4-20
LOCKNUT
AUGER HUB
FIG. 18
AUGER SHAFT
3.
TO REMOVE BELT COVER (See Fig. 19)
Remove the two screws securing belt cover to frame.
2.   Remove belt cover.
Replace belt cover by installing cover and screws and
tighten securely.
1.
CAUTION: Do not substitute. Use only original
equipment shear bolts  as supplied with your
snow thrower.
4.
Insertsafetyignitionkeyandreconnectsparkplugwire
to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured  to the impeller shaft with two  (2)
capscrew/shearboltsandhexnuts.Shouldaforeignobject
or ice become  lodged in the impeller, the  capscrews are
designed to break, preventing damage to any other com-
ponents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear bolts:
FRAME
BELT COVER
FIG. 19
SCREWS
1.
Disengage all  controls  and move  throttle control  to
STOP position. Wait for all moving parts to stop.
15
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 40 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website