Checking and Adjusting the
Skids and Scraper
Yearly—Inspect the traction cable and adjust or
replace it if necessary.
If the machine does not drive in the forward or reverse speeds
or it drives when you release the traction lever, adjust the
traction cable.
Service Interval: Yearly—Check the skids and the scraper
and adjust them if necessary.
Check the skids and the scraper to ensure that the auger does
not contact the paved or gravel surface. Adjust the skids and
the scraper as needed to compensate for wear.
If the left hand (traction) cable is not properly adjusted, do
the following steps:
1.
Loosen the jam nut.
1.
Check the tire pressure. Refer to Checking the Tire
Pressure.
2. Engage the traction lever and hold it in place (Figure
37).
2.
Loosen the nuts that secure both skids to the auger
sides until the skids slide up and down easily.
Figure 37
1
g019046
3.
Loosen or tighten the turnbuckle to adjust spring
length to 2.18 inches (5.5 cm) (Figure 38).
Figure 36
1.
1/8 inch (3 mm)
Important: The auger blades must be supported
above the ground by the skids.
3.
Ensure that the scraper is 1/8 inch (3 mm) above and
parallel to a level surface.
Note: If the pavement is cracked, rough, or uneven,
adjust the skids to raise the scraper. For gravel surfaces,
adjust the skids further down to prevent the machine
from picking up rocks.
4
g019048
4.
5.
Move the skids down until they are even with the
ground.
Firmly tighten the nuts that secure both skids to the
auger sides.
3
Note: To quickly adjust the skids if they loosen,
support the scraper 1/8 inch (3 mm) off the pavement,
then adjust the skids down to the pavement.
Figure 38
Note: If the skids become excessively worn, you can
turn them over and set the unused side toward the
pavement.
1.
Jam nut
3.
4.
Spring
2.
Turnbuckle
2.18 inches (5.5 cm)
Checking and Adjusting the
Traction Cable
4. Tighten the jam nut (Figure 38), ensuring there is slight
tension on the cable.
5.
If the traction cable is properly adjusted but a problem
remains, contact an Authorized Service Dealer.
Service Interval: After the first 2 hours—Inspect the
traction cable and adjust it if necessary.
20
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 37772, Toro Power Max 826 OE |
| Model Number | 37772 |
| Model Year | 2014 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 314000001 - 314999999 |
| Product Name | Power Max 826 OE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | 18 oz. (.54l) 30w or 10w-30 / API SF or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | 12D1050172F8 |
| Engine Motor Size | 205cc |
| Engine Motor Type | 4 Cycle |
| Engine Speed | 3300±100 RPM |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Tire Pressure | 17-20 PSI / 116-137 kPa |
| Spark Plug | Champion QC12YC |
| Spark Plug Gap | .030"/ .76mm |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)