Adjusting the Discharge Chute Storage
Latch
WARNING
If the discharge chute does not lock into the desired position
or does not unlock so that you can move it to another
position, adjust the discharge chute latch.
•
•
•
Gasoline vapors can explode.
Do not store gasoline more than 30 days.
1.
Loosen the clamp fastener on the chute support plate
until the cable is free.
Do not store the machine in an enclosure near
an open flame.
•
Allow the engine to cool before storing it.
Preparing the Machine for
Storage
1
1.
On the last refueling of the year, add fuel stabilizer to
fresh fuel as directed by the engine manufacturer.
2
3
Note: Fuel should not be stored longer than suggested
by the fuel stabilizer manufacturer.
2.
Run the engine for 10 minutes to distribute the
conditioned fuel through the fuel system.
3.
4.
5.
Run the machine until the engine runs out of fuel.
Prime the engine and start it again.
g019021
Figure 49
Allow the engine to run until it stops. When you can
no longer start the engine, it is sufficiently dry.
1.
Cable conduit
Cable clamp
3. Clamp fastener
6.
7.
8.
9.
Stop the engine and allow it to cool.
Remove the ignition key.
2.
2.
Remove any slack in the cable by pulling the cable
conduit rearward.
Clean the machine thoroughly.
Touch up chipped surfaces with paint available from an
Authorized Service Dealer. Sand affected areas before
painting, and use a rust preventative to prevent the
metal parts from rusting.
3.
Tighten the clamp fastener while holding the cable in
place.
Replacing the Drive Belts
10.
11.
Tighten all loose screws, bolts, and locknuts. Repair or
replace any damaged parts.
If the auger/impeller drive belt or the traction drive belt
becomes worn, oil-soaked, or otherwise damaged, have an
Authorized Service Dealer replace the belt.
Cover the machine and store it in a clean, dry place out
of the reach of children.
Removing the Machine from
Storage
1.
Remove the spark plug and spin the engine rapidly
using the starter to blow the excess oil from the
cylinder.
2.
3.
4.
Install the spark plug and tighten it firmly.
Connect the spark plug wire.
Perform the annual maintenance procedures as given
in the Recommended Maintenance Schedule.
24
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 37775, Toro Power Max 724 OE |
| Model Number | 37775 |
| Model Year | 2015 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 315000001 - 315999999 |
| Product Name | Power Max 724 OE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 26 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | 18 oz. (.54l) 30w or 10w-30 / API SF or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | 12D1050172F8 |
| Engine Motor Size | 205cc |
| Engine Motor Type | 4 Cycle |
| Engine Speed | 3300±100 RPM |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Tire Pressure | 17-20 PSI / 116-137 kPa |
| Spark Plug | Champion QC12YC |
| Spark Plug Gap | .030"/ .76mm |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)