OPERATION
Auger Control
The auger control is located on the left handle. Squeeze the auger
control to engage the augers. Release to stop the snow throwing
action. The drive control must also be released in order to stop auger
#(54%�$)2%#4)/.!,�#/.42/,
$)3#(!2'%
,%&4
$)3#(!2'%
2)'(4
!5'%2
#/.42/,
#(54%�4),4
$/7.
#(54%�4),4
50
Wheel SteeringControls
The left and right wheel steering controls are located
on the underside of the handles. Squeeze the right
control to turn right; squeeze the left control to turn
left.
'/
Drive Control / Auger Control Lock
The drive control is located on the right handle. Squeeze the drive
control to engage the wheel drive. Release to stop.
NOTE: Operate the snow thrower in open areas until you are familiar
with these controls.
This same lever also locks the auger control so you can operate the
chute crank without interrupting the snow throwing process. If the
auger control is engaged simultaneously with the drive control, the
operator can release the auger control (on the left handle) and the
augers will remain engaged. Release the drive control to stop the
augers and wheel drive (the auger control must also be released).
Chute Clean-Out Tool
WARNING: Never use your hands to clear a clogged
chute assembly. Shut off engine and remain behind
handles until all moving parts have stopped before
unclogging.
IMPORTANT: NEVER reposition the shift lever (change speeds or
direction of travel) without first releasing the drive control and bringing
the snow thrower to a complete stop. Doing so will result in premature
wear to the snow thrower’s drive system.
The clean-out tool is conveniently fastened to the rear of the auger
housing with a mounting clip.
1.
2.
3.
4.
Release both the auger control and the drive/auger control lock.
Stop the engine by moving the throttle to the stop position.
Remove the clean-out tool from the mounting clip.
$2)6%
#/.42/,
Use the shovel-shaped end of the clean-out tool to remove any
snow and ice in the chute assembly.
Re-fasten the clean-out tool to the mounting clip on the rear of the
auger housing and restart engine.
While standing in the operator’s position (behind the snow thrower),
engage the auger control for a few seconds to clear any remaining
snow or ice from the chute assembly before continuing to clear
snow.
5.
6.
'
/
Two-Way Chute Control™)
Skid Shoes
This two-way control lever is meant to control the distance of snow
discharge from the chute. Tilt the lever forward or rearward to adjust
the distance snow will be thrown.
Position the skid shoes based on surface conditions. Adjust upward
for hard-packed snow. Adjust downward when operating on gravel or
crushed rock surfaces. See “Making Adjustment” Section.
Chute Directional Control
Headlight
The chute directional control is located on left side of the snow thrower. The headlight is on whenever the engine is running.
To change the direction in which snow is thrown, turn chute directional
control as follows:
•
Crank clockwise to discharge to the left.
•
Crank counterclockwise to discharge to the right.
12
| Categories | Craftsman Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Craftsman C459.52833 |
| Model Number | C459-52833 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Product Name | Craftsman 45-Inch Large Frame Steerable Snow Thrower |
| Product Brand | Craftsman. Customer Service Representatives are available by phone: Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Swath | 45 inch |
| Document File Type | |
| Publisher | craftsman.com |
| Wikipedia's Page | Craftsman (tools) |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)