MTD 190-627 600 Series 42-Inch Snow Blower Owners Manual

SECTION 4:  ASSEMBLY
WARNING:   Before    installing   attachment,
place tractor on a firm and level surface. Place
the PTO in the disengaged (OFF) position, set
the parking brake, shut engine off and remove
key to prevent unintended starting.
NOTE: Your tractor’s cutting deck and PTO belt must
be   removed  prior   to   mounting  the   snow   thrower
attachment. Refer to your tractor’s Operator’s Manual
for detailed instructions. Retain all the deck hardware
and store it in a safe place. If your tractor is equipped
with any front-end accessory such as a front bumper
kit, it must also be removed.
Hex Screw,
Belleville Washer
NOTE:  It   is  strongly  recommended   that  a  second
person act as an assistant throughout the assembly of
the snow thrower attachment. Having a second person
present eases the completion of many of the steps.
NOTE: The lock washer and hex nut
are on the INSIDE of the pivot bracket.
Figure 4
Mounting the Support Carriage Assembly
1.
Fasten the provided hex screws, belleville washers,
lock washers and lock nuts to the tractor’s front
pivot bracket as illustrated in Figure 4 on both the
left side and the right side. Do NOT tighten the
hardware at this point in the assembly.
Front Pivot Bar
2.
3.
4.
Place the tractors front tires on 2x4s to bring the
tractor’s front end up a few inches and allow
clearance for positioning the support carriage.
Remove the hex screws, lock washers and hex
nuts from the both sides of the rear of the support
carriage assembly.
Place the support carriage assembly between the
tractor’s front tires so that the large notch on both
sides of the support carriage straddles the tractor’s
front pivot bar. See Figure 5.
Large Notch
Support Carriage
5.
Position the rear of the support carriage so that the
holes where the hardware was just removed align
with the holes in the tractor’s frame rail.
Figure 5
NOTE: Make certain that the support carriage is to the
OUTSIDE of the frame rail on both sides of the tractor.
6.
Reinsert the rearmost hex screw removed in Step 3
through the aligning holes in both the support
carriage assembly and the tractor’s frame rail.
Fasten with the lock washer and hex nut but do not
tighten the hardware at this time. See Figure 6.
Pivot the front of the support carriage upward until
the small grooves found in the front portion of
support carriage slide between the belleville
washers inserted in step 1 and the tractor’s front
pivot bracket. See Figure 7.
7.
Hex Screw
NOTE: The lock washer and hex nut are
on the INSIDE of the tractor’s frame rail.
Figure 6
6
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 20 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “MTD 190-627 600 Series 42-Inch Snow Blower Owners Manual

  1. What lawn tractors will a MTD OEM 190-627 42 inch two stage snow thrower fit. I’m selling one and I want to make sure that the person who buys is has a mower that it will fit properly. How can I get a list of mowers that will work with it.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website