MTD 44M 46M Series 21 Inch Self Propelled Rotary Lawn Mower Owners Manual

5
6
Before reassembling the blade and the blade adapter
to the unit, lubricate the engine crankshaft and the
inner surface of the blade adapter with light oil.
7.
Install the blade adapter on the crankshaft with the
“star” away from the engine. See Figure 5-2. Place
the blade with the side marked “bottom” (or with part
number) facing away from the adapter. Align the blade
bell support over the blade with the tabs in the holes
of the blade and insert the hex bolt.
Maintenance
8.
Tighten the hex bolt to the torque listed below:
Blade Mounting Torque
Center Bolt 450 in. lb. min., 600 in.lb. max.
To insure safe operation of your unit, ALL nuts and bolts
must be checked periodically for correct tightness.
Belt Care
1.  Remove two shoulder screws securing front drive
WARNING
cover to mower deck. See Figure 5-3. Press inward on
sides of front drive cover and release tabs that secure
it to the height adjuster brackets. Remove drive cover
from mower.
Loosen screw holding belt tension spring to transmis-
sion. See Figure 5-3 inset. Do not remove screw
completely. As you loosen it, tension on the belt will be
released.
Push transmission up a little and slide belt off the
transmission pulley. Lift mower to access belt from
underside of mower. Slide belt off of engine pulley and
around the blade. See Figure 5-4.
Replace with new belt, working around blade. Make
sure belt is firmly seated on engine pulley while pulling
from the other side and sliding it around the transmis-
sion pulley. Tighten screw loosened earlier to secure
belt tension spring to the transmission. Reassemble
front drive cover.
Figure 5-2
When removing the
cutting blade or belt,
protect your hands
with a pair of heavy
gloves or use a heavy
rag to hold the blade.
2.
3.
4.
An unbalanced blade
will cause excessive
vibration when rotat-
ing at high speeds. It
may cause damage
to mower, and could
break causing per-
sonal injury.
Off-Season Storage
The following steps should be taken to prepare your lawn
mower for storage.
Figure 5-3
1.
2.
3.
4.
5.
Clean and lubricate mower thoroughly as described in
the lubrication instructions.
We do not recommend
the use of pressure
washers or garden
hose to clean your
unit. These may cause
damage to electrical
components, spindles,
pulleys, bearings, or
the engine. The use
of water will result in
shortened life and
We do not recommend the use of a pressure washer
or garden hose to clean your unit.
Refer to engine manual for correct engine  
storage instructions.
Coat mower’s cutting blade with chassis grease to
prevent rusting.
Store mower in a dry, clean area. Do not store next to
corrosive materials, such as fertilizer.
NOTE: When storing any type of power equipment in
a poorly ventilated or metal storage shed, care should
be taken to rust-proof the equipment. Using a light oil or
silicone, coat the equipment, especially cables and all
moving parts of your lawn mower before storage.
reduce serviceability.
Figure 5-4
11
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 52 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website