To Engage Drive
•
Pull the starter handle with a firm, rapid stroke.
IMPORTANT: Do not release the handle and allow it to
snap back. Keep a firm hold on the starter handle and
allow it to slowly recoil.
•
With the throttle control in the Fast (rabbit) position,
move shift lever into one of the five forward (F)
positions or two reverse (R) positions. Select a
speed appropriate for the snow conditions and a
pace you’re comfortable with.
•
As the engine warms, slowly rotate the choke
control to the OFF position. If the engine falters,
quickly rotate the choke control back to the FULL
position and then slowly into the OFF position
again.
IMPORTANT: Use the slower speeds until you are
comfortable and familiar with the operation of the snow
thrower.
•
Squeeze the auger control against the handle and
the augers will turn. Release it and the augers will
stop.
Squeeze the drive control against the handle the
snow thrower will move. Release it and drive
motion will stop.
Stopping The Engine
•
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To help prevent possible starter freeze-up, proceed
as follows:
•
•
Electric Starter (on models so equipped)
IMPORTANT: NEVER reposition the shift lever (change
speeds or direction of travel) without first releasing the
drive control and bringing the snow thrower to a
complete stop. Doing so will result in premature wear to
the snow thrower’s drive system.
1.
Connect extension cord to the electric starter outlet
on the engine, then to 120 volt AC outlet.
With the engine running, push the starter button
and allow the starter for spin for several seconds.
The noise made by the starter is normal. The
engine’s starter is not being harmed.
When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow
thrower.
2.
To Engage Augers
3.
•
To engage the augers and start throwing snow,
squeeze the auger control against the left handle.
Release to stop the augers.
Auger Control Test
4.
5.
6.
Move throttle control to STOP position.
Remove the ignition key.
Wipe all snow and moisture from the carburetor
cover in the area of the drive control and auger
control. Also, engage and release the controls
several times.
IMPORTANT: Perform the following test before
operating your snow thrower for the first time and at the
start of each winter season.
Check the adjustment of the auger control as follows:
•
When the auger control is released and in the
disengaged “up” position, the cable should have
very little slack. It should NOT be tight.
NOTE: Keep the key in a safe place. The engine
cannot start without the ignition key.
Recoil Starter
•
In a well-ventilated area, start the snow thrower
engine as instructed earlier in this section under the
heading Starting the Engine. Make sure the throttle is
set in the FAST position.
While standing in the operator’s position (behind
the snow thrower), engage the auger.
1.
With engine running, pull starter rope with a rapid,
continuous full arm stroke three or four times.
Pulling the starter rope will produce a loud
clattering sound, which is not harmful to engine.
Move throttle control to STOP position.
Remove the ignition key.
•
•
2.
3.
Allow the auger to remain engaged for
approximately ten (10) seconds before releasing
the auger control. Repeat this several times.
With the throttle control in the FAST (rabbit)
position and the auger control in the disengaged
“up” position, walk to the front of the machine.
Confirm that the auger has completely stopped
rotating and shows NO signs of motion.
NOTE: Keep the key in a safe place. The engine
cannot start without the ignition key.
•
•
4.
Wipe all snow and moisture from the carburetor
cover in the area of the drive control and auger
control. Also, engage and release the controls
several times.
IMPORTANT: If the auger shows ANY signs of rotating,
immediately return to the operator’s position and shut
off the engine. Wait for ALL moving parts to stop before
re-adjusting the auger control.
11
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | MTD 6DE, MTD Snow Blower Manual |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)