Starting the Engine
4
5
6
.
.
.
Once activated (indicator light ON), the tractor can be
driven in reverse with the cutting blades (PTO) engaged.
WARNING! Do not operate the tractor if the
interlock system is malfunctioning. This system was
designed for your safety and protection.
Always look down and behind before and while backing to
make sure no children are around.
After resuming forward motion, return the key to the
NORMAL MOWING position.
NOTE: Refer to the Gasoline and Oil fill-up instructions in the
Assembly & Set-up section of this manual.
IMPORTANT: The REVERSE CAUTION MODE will remain
activated until:
1
.
Insert the tractor key into the ignition switch.
a. The key is placed in either the NORMAL MOWING
position or STOP position.
2.
Place the PTO (Blade Engage) lever in the disengaged (OFF)
position.
b. The operator engages the parking brake by fully
depressing the clutch-brake pedal and holding it
down while moving the speed control lever into the
PARK BRAKE position.
3.
Engage the tractor’s parking brake.
Activate the choke control.
4
5
.
.
Turn the ignition key clockwise to the START position. After
the engine starts, release the key. It will return to the ON (or
Normal Mowing) position.
Engaging the Parking Brake
To engage the parking brake:
CAUTION: Do NOT hold the key in the START
position for longer than ten seconds at a time.
Doing so may cause damage to your engine’s
electric starter.
1
2
3
.
.
.
Fully depress the clutch-brake pedal and hold it down with
your foot.
Move the speed control lever all the way down and into the
parking brake position.
6.
After the engine starts, deactivate the choke control and
place the throttle control in the FAST position.
Release the clutch-brake pedal to allow the parking brake
to engage.
NOTE: Do NOT leave the choke control on while operating the
tractor. Doing so will result in a “rich” fuel mixture and cause the
engine to run poorly.
To release the parking brake:
1
.
Depress the clutch-brake pedal and move the speed
control lever out of the parking brake position and into a
desired speed.
Stopping the Engine
WARNING! If you strike a foreign object, stop the
engine, disconnect the spark plug wire(s) and
ground against the engine. Thoroughly inspect the
machine for any damage. Repair the damage before
restarting and operating
Setting the Cutting Height
1
.
Select the height position of the cutting deck by placing
the deck lift lever in any of the six different cutting height
notches on the right side of the fender.
1
2
3
.
.
.
If the blades are engaged, place the PTO (Blade Engage)
lever in the disengaged (OFF) position.
2
.
Adjust the deck wheels as instructed in the Assembly & Set-
Up section earlier in this manual, if equipped, so that they
are between ¼-inch and ½-inch above the ground when
the tractor is on a smooth, flat surface such as a driveway.
Turn the ignition key counterclockwise to the STOP
position.
Remove the key from the ignition switch to prevent
unintended starting.
WARNING! Keep hands and feet away from the
discharge opening of the cutting deck.
NOTE: On models so equipped, the deck wheels are an anti-scalp
feature of the deck and are not designed to support the weight
of the cutting deck. Refer to Leveling in the Maintenance section
of this manual for more detailed instructions regarding various
deck adjustments.
16
sectiOn 5— OperatiOn
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals |
|---|---|
| Tags | MTD 760, MTD 770 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
I need a parts manual. I need a deck idler spring for model. Series 760………… Model no.13am7725055. Serial number 1c170 b 70018