6.
7.
As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to FULL and then slowly into
the OFF position again.
When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow thrower.
Gas & Oil Fill-Up
Service the engine with gasoline and oil as instructed in
the Tecumseh Engines manual packed separately with
your snow thrower. Read instructions carefully.
Starting The Engine
1.
Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
(inside the rubber boot) is fastened securely over the
metal tip on the spark plug.
WARNING
Recoil Starter
1.
Rotate choke control to FULL choke position (cold
engine start).
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
2. Make certain both the auger control and drive control
are in the disengaged (released) position.
3. Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not attempt to turn the key.
NOTE:in the OFFIf thepositionengineinsteadis alreadyof FULL.warm, place choke control
2.
Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
NOTE:insertedTheintoengineignitioncannotswitch.start unless the key is
Use extreme care
when handling
NOTE:a short shutdown.DO NOT use primer to restart a warm engine after
Electric Starter
1.
Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
NOTE: Additional priming may be necessary if the
temperature is below 15° Fahrenheit.
WARNING: The optional electric
3.
Grasp the recoil starter handle and slowly pull the rope
out. At the point where it becomes slightly harder to
pull the rope, slowly allow the rope to recoil.
starter is equipped with a
grounded three-wire power cord
and plug, and is designed to op-
erate on 120 volt AC household
current. It must be used with a
properly grounded three-prong
receptacle at all times to avoid
the possibility of electric shock.
Follow all instructions carefully
prior to operating the electric
starter.
4. Pull the starter handle with a firm, rapid stroke. Do not
release the handle and allow it to snap back. Keep a
firm hold on the starter handle and allow it to slowly
recoil.
5. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to the FULL position and then
slowly into the OFF position again.
If your home’s
wiring system is not a
three-wire grounded
system, do not use
this electric starter
under any conditions.
NOTE: Allow the engine to warm up for a few minutes
If you have a grounded three-prong receptacle, proceed after starting. The engine will not develop full power until it
as follows:
reaches operating temperatures.
1.
Plug the extension cord into the outlet located on
the engine’s surface. Plug the other end of extension
cord into a three-prong 120-volt, grounded, AC outlet
in a well-ventilated area.
Stopping The Engine
Run engine for a few minutes before stopping to help dry
off any moisture on the engine.
2.
Rotate choke control to FULL choke position (for a
1.
2.
3.
Move throttle control to STOP position.
If your home
cold engine start).
Remove the ignition key and store in a safe place.
electrical system
is grounded, but a
three-hole receptacle
is not available, do
not use your snow
thrower’s electric
starter.
Wipe all snow and moisture from the area around the
engine as well as the area in and around the drive
control and auger control. Also, engage and release
both controls several times.
NOTE:control inIf thethe engineOFF positionis alreadyinsteadwarm,of FULL.place choke
3. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
4.
5.
Push starter button to start engine.
Once the engine starts, release starter button.
10
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | MTD 769-01275D, MTD Snow Blower Manual |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)