MTD Columbia 769-03265 Snow Blower Owners Manual

6
Maintaining
Your Snow
Thrower
Engine
Refer to the separate engine manual packed with your
unit for all engine maintenance.
Lubrication
Engine
Refer to the separate engine manual packed with your
unit for all engine lubrication instructions.
Gear Shaft
The gear (hex) shaft should be lubricated  at least once
a season or after every 25 hours of operation.
1.
2.
3.
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
Remove the lower frame cover by removing the two
screws which secure it.
Apply a light coating of an all-weather multi-purpose
oil to the hex shaft. See Figure 6-1.
Figure 6-1
NOTE:aluminumAvoiddrivegettingplate.oil on rubber friction wheel and
3HEAR�0IN
3PACERS
"EARING
Wheels
WARNING
At least once a season, remove both wheels. Clean and
coat the axles with a multipurpose automotive  grease
before reinstalling wheels.
Before lubricating,
repairing, or inspect-
ing, disengage all
controls and stop
engine. Wait until all
moving parts have
come to a complete
stop.
Chute Directional Control (optional)
Once a season, the joystick should be lubricated  with
petroleum jelly, linseed oil, mineral oil, paraffin wax or
3-in-1
oil.
Auger Shaft
At least once a season, remove the shear pins on auger
shaft. Spray lubricant inside shaft,  around the spacers.
Also lubricate the flange bearings found at either  end of
the shaft. See Figure 6-2.
Figure 6-
Augers
The augers are secured to the spiral shaft with two
shear pins and cotter pins. If the auger should strike
a foreign object or ice jam, the snow thrower is
designed so that the pins may shear. Refer to Figure
6-2.
If the augers will not turn, check to see if the pins
have sheared. One set of replacement shear pins
has been provided with the snow thrower. When
replacing pins, spray an oil lubricant into shaft before
inserting new pins.
Keep all grease and oil
off of the rubber friction
wheel and aluminum
drive plate.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when  necessary.
To remove skid shoes:
Figure 6-3
To remove shave plate:
1.
Removewhich securethe fourthemcarriageto the snowbolts andthrower.hex flange nuts
1.  Remove the carriage  bolts and hex nuts which attach
it and the skid shoes to the snow thrower housing.
2.  Reassemble new shave plate, making sure heads  of
carriage bolts are to the inside of housing. Tighten
securely.
2.
Reassemble new skid shoes with the four carriage
bolts (two on each side) and hex flange  nuts. Refer
to Figure 6-3.
16
Product Specification
CategoriesColumbia Snow Blower Manuals, MTD Snow Blower Manuals, Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 52 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated MTD Columbia 769-03265 Snow Blower Owners Manual 4.0 out of 4.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

MTD Columbia 769-03265 Snow Blower Owners Manual SKU UPC Model
jpy on Dec 20, 2014. mtd manual

mtd manual


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website