MTD Troy-Bilt RZT Series Tractor Lawn Mower Owners Manual

3
Assembly & Set-Up
Contents of Crate
One Lawn Tractor
One Oil Drain Tube
One Deck Wash Hose Coupler
One Product Registration Card
One RZT  Tractor Operator’s
Manual
One Kohler Engine Operator’s
Manual
TRACTOR PREPARATION
Remove the upper crating material from the shipping
pallet, and cut any bands or tie straps securing the tractor
to the pallet.
4.     Align the grooves in the seat adjust spacers with the
sides of the adjustment slots in the pivot bracket.
5
.
Slide the seat adjust spacers into the slots of the pivot
bracket.
6
.
Continue to push the seat forward in the pivot bracket
until the front/left shoulder bolt of the seat assembly
passes forward of the stop bracket on the seat pivot
bracket. See Figure 3-2.
Use the lift handle to raise the deck to its highest position.
Engage the transmission bypass rods on each side of the
tractor; then carefully roll the tractor off the shipping
pallet. Disengage the bypass rods.  See Figure 3-1.
RH Transmission
Bypass Rod
Pull Out
Adjustment
Slots
Bypass Rod
Seat
Seat
Then Lower
In Slot
Pivot
Bracket
Seat
Adjust
Spacer
Keyhole
Slot
Front/Left
Shoulder Bolt
Seat Adjust
Lever
Figure 3-1
Stop Bracket
Remove the deck wash system nozzle adapter from the
manual bag and store for future use.
Figure 3-2
Install Operator’s Seat
Refer to “Adjusting Operator’s Seat”  in Maintenance &
The operator’s seat was partially inserted into the seat
pivot bracket for shipping purposes. To install the seat
proceed as follows:
Adjustments  for seat adjustment instructions.
Position Drive Control levers
1
.
Cut any straps securing the seat assembly and the
The drive control levers of the tractor are lowered for
drive control levers to the tractor. Remove any packing      shipping purposes. The flange  lock nuts, hex screws, and
material.
flat washers that normally secure the control levers in
their operating position are unfastened and installed in
the slotted holes of the control levers for shipment. The
control levers must be repositioned to operate the tractor.
To reposition the control levers for operation, proceed as
follows:
NOTE: The seat is partially inserted into the slots of the seat
pivot bracket. If the seat does not become disengaged from
the pivot bracket when removing the packaging material, the
pivot bracket may be pivoted upward and the seat pushed
into place as described in step 6. If the seat does disengage the
pivot bracket, install the seat as instructed in steps 2 thru 6.
1.     Remove the hex screw, flat washer, and flange lock nut
from the slot of one of the drive control levers.
2
.
Pivot the seat pivot bracket partially upward. Refer to
Figure 3-2.
2
.
Lift and swing that control lever upward until the
slotted hole in the lever bracket aligns with one of the
holes in the pivot bracket. Refer to Figure 3-3.
3
.
Note the grooves in the seat adjust spacers attached
to the bottom of the seat, then lift the seat and
position above and to the rear of the pivot bracket.

Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 72 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website