4
Operating
Your
Chipper
Shredder
Vacuum
WARNING: Use extreme care when
handling gasoline. Gasoline is ex-
tremely flammable and the vapors are
explosive. Never fuel machine indoors
or while the engine is hot or running.
Extinguish cigarettes, cigars, pipes, and
other sources of ignition.
Throttle Control
Choke Control
Gas and Oil Fill-Up
1.
Check oil level and add oil if necessary. Follow engine
manual for this. See Figure 4-1 for location of the oil
fill.
2.
Service the engine with gasoline as instructed in the
engine manual. See Figure 4-1 for location of gas fill.
WARNING: Never fill fuel tank indoors
with engine running or until the engine
has been allowed to cool for at least two
minutes after running.
Figure 4-
7.
Repeat the previous steps until engine fires. When
engine starts, move choke control (if equipped)
gradually to RUN position.
Starting Engine
WARNING
8.
If engine falters, move choke control back toward the
IMPORTANT: The bag/chute switch button must be fully
depressed by the tip of front tab on bag handle or blower
chute for engine to start.
throttle control and repeat steps 5 through 7.
9. ALWAYS keep the throttle control in the START/RUN
position when operating the Chipper shredder
Vacuum.
Use extreme care when
handling gasoline.
Gasoline is extremely
flammable and the
vapors are explosive.
Never fuel machine
indoors or while
1.
2.
Attach spark plug wire to spark plug.
Make sure safety switch wire is connected to engine
and properly grounded to mounting bracket.
WARNING: Never run the engine
indoors or in a poorly ventilated area.
Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
3.
Engines with choke lever:
Move choke lever on engine to CHOKE position. (A
warm engine may not require choking).
the engine is hot or
running. Extinguish
cigarettes, cigars,
pipes, and other
Engines with primer:
Stopping Engine
Prime engine as instructed in separate engine manual. 1. Move throttle control lever to slow (turtle) position.
Whenever possible, gradually reduce engine speed
before stopping engine.
4.
5.
6.
The throttle control lever is located on the engine.
Move engine throttle control lever to FAST or START
position. See Figure 4-2.
sources of ignition.
2
.
.
Move throttle control lever to STOP or OFF
position.
Grasp starter handle and pull rope out slowly until
engine reaches start of compression cycle (rope will
pull slightly harder at this point).
Pull rope with a rapid, continuous, full arm stroke.
Keep a firm grip on starter handle. Let rope rewind
slowly.
3
Disconnect spark plug wire and ground it to the
retaining post to prevent accidental starting while
the equipment is unattended.
Never fill fuel tank
indoors with engine
running or until the
engine has been
NOTE: See your engine manual packed with your unit
for more detailed instructions.
allowed to cool for at
least two minutes after
running.
Never run the engine
indoors or in a poorly
ventilated area. Engine
exhaust contains
carbon monoxide, an
odorless and deadly
gas.
9
| Categories | Blower Vacuum and Sweeper Manuals, Lawn Mower Manual, MTD Blower and Vacuum Manuals, MTD Lawn Mower Manuals, Troy-Bilt Blower and Vacuum Manuals, Troy-Bilt Lawn Mower Manuals |
|---|---|
| Tags | MTD 060, Troy-Bilt Yard 060 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)