If the tractor does not come to a complete stop when the NOTE: Threading the ball joints too far onto the drag
brake pedal is completely depressed, or if the tractor’s
rear wheels can roll with the parking brake applied, the
brake is in need of adjustment. See an authorized Service
Dealer to have your brakes properly adjusted.
links will cause the front tires to “toe-in” too far. Proper
toe-in is between 1/16” and 5/16”.
Front tire toe-in can be measured as follows:
1.
Place the steering wheel in position for straight
Adjusting
Your Lawn
Tractor
Seat Adjustment
ahead travel.
2.
In front of the axle, measure the distance horizontally
from the inside of the left rim to the inside of the right
rim. Note the distance.
Behind the axle, measure the distance horizontally
from the inside of the left rim to the inside of the right
rim. Note the distance.
The measurement taken in front of the axle should
be between 1/16” and 5/16” less than the measure-
ment taken behind the axle. Adjust if necessary.
Quick Adjust Seat (If so equipped)
WARNING: Before operating this
machine, make sure the seat is
engaged in the seat stop, stand
behind the machine and pull back
on seat until fully engaged into stop.
3.
4.
•
To adjust the position of the seat on models equipped
with a seat adjustment lever, move the lever to the left
and slide the seat forward or rearward. Refer to the
Set-Up section. Make sure seat is locked into position
before operating the tractor.
WARNING
Knob Adjustment Seat (if so equipped)
Before operating this
machine, make sure
the seat is engaged in
the seat stop, stand
behind the machine
and pull back on seat
until fully engaged into
stop.
To adjust the position of the seat on models so equipped,
loosen the two knobs on the bottom of the seat. Refer to
the Set-Up section. Slide the seat forward or backward as
desired. Retighten the two knobs.
Standard Seat (if so equipped)
(EX�.UT
To adjust the position of the seat, loosen the two hex
screws on the bottom of the seat. Slide the seat forward
or backward as desired. Retighten the two screws. Refer
to the Set-Up section.
$RAG�,INK
Steering Adjustment
If the tractor turns tighter in one direction than the other,
or if the ball joints are being replaced due to damage or
wear, the steering drag links may need to be adjusted.
Adjustinto thetheballdragjointlinkson theso leftthatandequalrightlengthsside: are threaded
"ALL�
OINT
*AM�
.UT
*
Figure -3
1.
Loosenof the ballthejoint.jam Seenut foundFig. 5-3.on the drag link at the rear
Remove hex nut on the top of ball joint. See Fig. 5-3.
Thread the ball joint toward the jam nut to shorten the
drag link. Thread the ball joint away from the jam nut
to lengthen the drag link.
2.
3.
NOTE: Threading the
ball joints too far onto
the drag links will cause
the front tires to “toe-in”
too far. Proper toe-in
is between 1/16” and
5/16”.
4.
Replace hex nut and retighten the jam nut after proper
adjustment is achieved.
1
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, White Outdoor Lawn Mower Manuals |
|---|---|
| Tags | MTD 606, White Outdoor 606 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
Magnificent website. Plenty of helpful info here. I’m sending it to several buddies ans additionally sharing in delicious. And certainly, thanks in your sweat!