MTD White Outdoor 769-04123 Snow Blower Owners Manual

6
Engine
Refer to the separate engine manual packed with your
unit for all engine maintenance.
Lubrication
Engine
Refer to the separate engine manual packed with your
Maintaining
unit for all engine lubrication instructions.
Your Snow        Gear Shaft
The gear (hex) shaft should be lubricated at least  once
a season or after every 25 hours of operation.
Thrower
WARNING: Run the engine com-
pletely dry of gasoline before tipping
snowthrower.
Figure 6-1
1.
2.
3.
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
Remove the lower frame cover by removing the
screws which secure it.
3HEAR�0IN
3PACERS
"EARING
Apply a light coating of an all-weather multi-purpose
oil to the hex shaft. See Figure 6-1.
WARNING
NOTE:aluminumAvoiddrivegettingplate.oil on rubber friction wheel and
Before lubricating,
repairing, or inspect-
ing, disengage all
controls and stop
engine. Wait until all
moving parts have
come to a complete
stop.
Wheels
At least once a season, remove both wheels. Clean and
coat the axles with a multipurpose automotive grease
before reinstalling wheels.
Auger Shaft
At least once a season, remove the shear pins on auger
shaft. Spray lubricant inside shaft, around  the spacers.
Also lubricate the flange bearings found at either end of
the shaft. See Figure 6-2.
Figure 6-2
Run the engine
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when  necessary.
To remove skid shoes:
completely dry of
gasoline before
tipping snowthrower.
1.
Removewhich securethe fourthemcarriageto the snowbolts andthrower.hex flange nuts
Reassemble new skid shoes with the four carriage
bolts (two on each side) and hex flange  nuts. Refer
to Figure 6-3.
2.
To remove shave plate:
Remove the carriage bolts and hex nuts which attach   Augers
Figure 6-3
1.
it and the skid shoes to the snow thrower housing.
Keep all grease and oil
off of the rubber friction
wheel and aluminum
drive plate.
The augers are secured to the spiral shaft with two
shear pins and cotter pins. If the auger should strike a
foreign object or ice jam, the snow thrower is designed
so that the pins may shear. Refer to Figure 6-2.
2.  Reassemble new shave plate, making sure heads of
carriage bolts are to the inside of housing. Tighten
securely.
If the augers will not turn, check to see if the pins have
sheared. One set of replacement shear pins has been
provided with the snow thrower. When replacing pins,
spray an oil lubricant into shaft before inserting new pins.
14
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, White Outdoor Snow Blower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 48 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated MTD White Outdoor 769-04123 Snow Blower Owners Manual 5.0 out of 5.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

MTD White Outdoor 769-04123 Snow Blower Owners Manual SKU UPC Model
William Kampe on Oct 20, 2013.



Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website