4
Auger Control
Chute Directional Control
!5'%2
#/.42/,
#(54%�$)2%#4)/.!,�#/.42/,
!$*534!",%
$)3#(!2'%
,%&4
$)3#(!2'%
2)'(4
#(54%�4),4
Operating
Your Snow
Thrower
'/
The auger control is located on the left handle. Squeeze
the control grip against the handle to engage the augers
and start snow throwing action. Release to stop.
The chute directional control is located on left side of the
snow thrower.
To change the direction in which snow is thrown, turn
chute directional control as follows:
Drive Control / Auger Clutch Lock
•
•
Crank clockwise to discharge to the left.
Crank counterclockwise to discharge to the right.
$2)6%
#/.42/,
Clean-Out Tool
WARNING: Never use your hands
WARNING
to clear a clogged chute assem-
bly. Shut off engine and remain
behind handles until all moving
parts have stopped before
The operation of
any snow thrower
can result in foreign
objects being thrown
into the eyes, which
can damage your
'
/
unclogging.
The chute clean-out tool is fastened to the top of the
The drive control is located on the right handle. Squeeze auger housing with a mounting clip. The tool is designed
the control grip against the handle to engage the wheel
drive. Release to stop.
to clear a clogged chute assembly.
NOTE: This item is fastened with a cable tie to the rear
of the auger housing at the factory. Cut the cable tie
before operating the snow thrower.
eyes severely. Always
wear safety glasses
while operating the
snow thrower, or while
performing any adjust-
ments or repairs on it.
The drive control also locks the auger control so that
you can operate the chute directional control without
interrupting the snow throwing process. If the auger
control is engaged simultaneously with the drive control,
the operator can release the auger control (on the left
handle) and the augers will remain engaged. Release
both controls to stop the augers and wheel drive.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces.
Be sure no one other
than the operator is
standing near the snow
thrower while starting
engine or operating
snow thrower. Never
run engine indoors or
in enclosed, poorly
ventilated areas. En-
gine exhaust contains
carbon monoxide, an
odorless and deadly
gas. Keep hands, feet,
hair and loose clothing
away from any moving
parts on engine and
snow thrower.
IMPORTANT: Always release the drive control before
changing speeds.
Electric Starter Outlet
Requires the use of a three-prong outdoor extension cord
(included) and a 120V power source/wall outlet.
Ignition Key
The ignition key is a safety devise. It must be fully
inserted in order for the engine to start. Remove the
ignition key when the snow thrower is not in use.
Augers
When engaged, the augers rotate and draw snow into the
auger housing.
NtheOTengine.E: Do nDoingot turnsothemayignicausetion keitytoinbreak.an attempt to start
Chute Assembly
Snow drawn into the auger housing is discharged out the
chute assembly.
Recoil Starter Handle
This handle is used to manually start the engine.
Gas Cap
Unthread the gas cap to add gasoline to the fuel tank.
Electric Starter Button
Pressing the electric starter button engages the engine’s
electric starter when plugged into a 120V power source.
9
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, White Outdoor Snow Blower Manuals |
|---|---|
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)