1.
2.
With the tractor parked on a firm, level surface, place
the deck lift lever in the top notch (highest position)
and rotate the blade nearest the discharge chute so
that it is parallel with the tractor.
Measure the distance from the front of the blade tip to
the ground and the rear of the blade tip to the ground.
The first measurement taken should be between 1/4”
and 3/8” less than the second measurement. Deter-
mine the approximate distance necessary for proper
adjustment and proceed, if necessary, to the next step.
From the front of the tractor, loosen the hex lock nut
on each end of the deck hanger rod, and turn away
from the inner hex nuts. See Fig. 5-1.
Tighten the inner hex nuts front against the front
hanger bracket to raise the front of the deck; loosen
the hex nuts to lower the front of the deck.
Adjusting
Your Lawn
Tractor
3.
4.
,
TO�LOWER�DECK
OOSEN
4IGHTEN
TO�RAISE�DECK
NOTE: Models with a 42-inch deck have only ONE jam
nut, washer, and lock nut.
WARNING
Figure -1
5.
Retighten the two lock nuts against the inner hex nuts
Never attempt to make
when proper adjustment is achieved.
any adjustments
Side to Side
while the engine
If the cutting deck appears to be mowing unevenly, a side
to side adjustment can be performed. Adjust if necessary
as follows:
is running, except
where specified in the
operator’s manual.
1.
With the tractor parked on a firm, level surface, place
the deck lift lever in the top notch (highest position)
and rotate both blades so that they are perpendicular
with the tractor.
Never attempt to
adjust the brakes
while the engine
is running. Always
disengage PTO, move
shift lever into neutral
position, stop engine
and remove key to
prevent unintended
starting.
2. Measure the distance from the outside of the left blade
tip to the ground and the distance from the outside of the
right blade tip to the ground. Both measurements taken
should be equal. If they’re not, proceed to the next step.
3.
Loosen,left deckbuthangerdo NOTbracket.remove,SeetheFig.hex5-2.cap bolt on the
!DJUSTMENT�'EAR
(EX�"OLT
4.
Balance the deck by using a wrench to turn the
adjustment gear (found immediately behind the hex
cap bolt just loosened) clockwise/up or counterclock-
wise/down. The deck is properly balanced when both
blade tip measurements taken earlier are equal.
Figure -
WARNING: Never attempt to make
any adjustments while the engine
is running, except where specified
in the operator’s manual.
5.
Retighten the hex cap bolt on the left deck hanger
bracket when proper adjustment is achieved.
Leveling the Deck
Parking Brake Adjustment
NOTE: Check the tractor’s tire pressure before perform-
ing any deck leveling adjustments. Refer to Tires on
page 24 for information regarding tire pressure.
WARNING: Never attempt to adjust
the brakes while the engine is run-
ning. Always disengage PTO, move
shift lever into neutral position, stop
engine and remove key to prevent
unintended starting.
Front To Rear
The front of the cutting deck is supported by a stabilizer
bar that can adjusted to level the deck from front to
rear. The front of the deck should be between 1/4-inch
and 3/8-inch lower than the rear of the deck. Adjust if
necessary as follows:
0
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, Yard Man Lawn Mower Manuals |
|---|---|
| Tags | MTD 604, Yard Man 604 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)