RULES FOR SAFE OPERATION
•
IMPORTANT SAFETY INSTRUCTIONS •
READ ALL INSTRUCTIONS BEFORE OPERATING
• Be sure the cutting attachment is not in contact with anything
before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position whenever
pulling the starter rope. The operator and unit must be in a stable
position while starting. Refer to Starting/Stopping Instructions.
• Use the right tool. Only use this tool for its intended purpose.
• Do not overreach. Always keep proper footing and balance.
•
•
•
•
•
Read the instructions carefully. Be familiar with the controls
and proper use of the unit.
Do not operate this unit when tired, ill, or under the influence
of alcohol, drugs, or medication.
Children and teens under the age of 15 must not use the unit,
except for teens guided by an adult.
All guards and safety attachments must be installed properly
before operating the unit.
Inspect the unit before use. Replace damaged parts. Check
for fuel leaks. Make sure all fasteners are in place and secure.
Replace parts that are cracked, chipped, or damaged in any
way. Do not operate the unit with loose or damaged parts.
•
•
•
•
Always hold the unit with both hands when operating. Keep
a firm grip on both handles or grips.
Keep hands, face, and feet at a distance from all moving parts. Do
not touch or try to stop the cutting attachment when it rotates.
Do not touch the engine, gear housing or muffler. These parts get
extremely hot from operation, even after the unit is turned off.
Do not operate the engine faster than the speed needed to
cut, trim or edge. Do not run the engine at high speed when
not cutting.
•
Carefully inspect the area before starting the unit. Remove all
debris and hard or sharp objects such as glass, wire, etc.
•
•
Be aware of the risk of injury to the head, hands and feet.
Clear the area of children, bystanders, and pets. At a
minimum, keep all children, bystanders, and pets outside a
•
•
Always stop the engine when cutting is delayed or when
50
feet (15 m) radius; there still may be a risk to bystanders
walking from one cutting location to another.
from thrown objects. Bystanders should be encouraged to
wear eye protection. If you are approached, stop the unit
immediately.
If you strike or become entangled with a foreign object, stop
the engine immediately and check for damage. Do not operate
before repairing damage. Do not operate the unit with loose or
damaged parts.
•
•
Use only 0.095 inch (2.41 mm) diameter original equipment
manufacturer replacement line. Never use metal-reinforced line,
wire or rope. These can break off and become dangerous
projectiles.
Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments or
repairs before using unit.
•
•
Stop the unit, switch the engine to off, and disconnect the
spark plug for maintenance or repair.
Use only original equipment manufacturer replacement parts
and accessories for this unit. These are available from your
authorized service dealer. Use of any unauthorized parts or
accessories could lead to serious injury to the user, or
damage to the unit, and void your warranty.
SAFETY WARNINGS FOR GAS UNITS
•
Store fuel only in containers specifically designed and approved
for the storage of such materials.
•
•
Keep unit clean of vegetation and other materials. They may
become lodged between the cutting attachment and shield.
To reduce fire hazard, replace a faulty muffler and spark
arrestor. Keep the engine and muffler free from grass,
leaves, excessive grease or carbon build up.
WARNING: Gasoline is highly flammable, and its
vapors can explode if ignited. Take the following
precautions:
OTHER SAFETY WARNINGS
•
•
•
•
Never store a fueled unit inside a building where fumes may
•
•
Avoid creating a source of ignition for spilled fuel. Do not
start the engine until fuel vapors dissipate.
Always stop the engine and allow it to cool before filling the
fuel tank. Never remove the cap of the fuel tank, or add fuel,
when the engine is hot. Never operate the unit without the
fuel cap securely in place. Loosen the fuel tank cap slowly to
relieve any pressure in the tank.
Mix and add fuel in a clean, well-ventilated outdoor area
where there are no sparks or flames. Slowly remove the fuel
cap only after stopping engine. Do not smoke while fueling
or mixing fuel. Wipe up any spilled fuel from the unit
immediately. Always wipe unit dry before using.
Move the unit at least 30 feet (9.1 m) from the fueling source
and site before starting the engine. Do not smoke or allow
sparks and open flames near the area while adding fuel or
operating the unit.
reach an open flame or spark.
Allow the engine to cool before storing or transporting. Be
sure to secure the unit while transporting.
Store the unit in a dry area, locked up or up high to prevent
unauthorized use or damage, out of the reach of children.
Never douse or squirt the unit with water or any other liquid.
Keep handles dry, clean and free from debris. Clean after
each use, see Cleaning and Storage instructions.
Keep these instructions. Refer to them often and use them
to instruct other users. If you loan someone this unit, also
loan them these instructions.
•
•
•
SAVE THESE INSTRUCTIONS
WHILE OPERATING
•
•
•
•
Never start or run the unit inside a closed room or building.
Breathing exhaust fumes can be fatal. Operate this unit only
in a well-ventilated outdoor area.
Wear safety glasses or goggles that meet ANSI Z87.1 standards
and are marked as such. Wear ear/hearing protection when oper-
ating this unit. Wear a face or dust mask if the operation is dusty.
Wear heavy long pants, boots, gloves and a long sleeve
shirt. Do not wear loose clothing, jewelry, short pants,
sandals or go barefoot. Secure hair above shoulder level.
The cutting attachment shield must always be in place while
operating the unit as a trimmer. Do not operate unit without
both trimming lines extended, and the proper line installed. Do
not extend the trimming line beyond the length of the shield.
•
•
2
This unit has a clutch. The cutting attachment remains
stationary when the engine is idling. If it does not, have the
unit adjusted by an authorized service technician.
Adjust the D-handle to your size in order to provide the best grip.
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, Yard Man Lawn Mower Manuals |
|---|---|
| Tags | MTD YM20CS, Yard Man YM20CS |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)