Simplicity 10.5 1694986 10530L Snow Blower Quick Setup Guide Manual

TP 1000-4518-03-LW-SN:QS_TroyBilt_REV7.qxd  11/5/2007  11:41 AM  Page 1
8
Spout Rotator Brake Cable Connection
2
Read the Operator’s Manual
Slide the spout rotator brake cable (E,  Figure 9) between the dash and the handle cross bar  as shown.
Slide the rubber dust cover (D,  Figure 10) off of plastic fitting (B).
Place “Z” bend of cable (C) into hole (G)  of brake lever assembly (E)
Pull plastic fitting (B) behind bracket (E).
Quick Setup Guide
Locate the operator’s manual in the manual  packet.
Always read and follow the instructions  in the operator’s
manual.  Proper care, performance tips, and safety
information are located in this important  document.
Two-Stage Snowthrower
• Slide chute  rotator cable (A) between slot in bracket (E) and push  forward to lock in place.
Slide the rubber dust cover (F)  over the plastic fitting (B).
“Right” and “Left” are from the Operating Position.
1694986
10530L, 10.5 Snowthrower
A
B
E
D
Speed Selector
Auger Engage
Control
D
E
3
Raise The Handles
A
B
Chute Deflector
Control
E
C
Chute Rotator
Control
G
C
E
C
C
Cut four orange zip ties (E, Figure  3) that secure control cables to
handle assembly (C).  Be careful not to cut  or damage the control
cables.
Loosen nuts (B) in upper holes with  a 1/2” wrench.  Rotate upper
handle assembly (A) up.  Locate two carriage  bolts and two 5/16
nuts in parts bag (B,  Figure 1).  Slide carriage bolts (D) and nuts
(B) into lower holes.  Tighten all hardware with a  1/2” wrench or
deep socket.
Traction
Engage
Control
Head Light
D
B
Figure 10
Fuel Cap
9
Remove Snowthrower From Crate
• Cut the  two zip ties from between wheels and the wood pallet.
Remove screws (A, Figure 11) from both  skid shoes (B).
Roll snowthrower off crate.
Easy Turn
Lever
Oil Dip
Stick
B
D
A
A
4   Install Chute Rotator Control Handle
Install thin jam nut (B, Figure 4)  onto chute rotator rod (C).  Install
chute rotator control handle (A) onto chute  rotator rod (C) turing at
least 10 full rotations.
Clean-Out
Tool
10  Add Oil and Fuel
Note: Engine is NOT shipped with oil.   Add 5W-30 premium engine oil.
See Engine Manual for complete engine oil  specifications and maintenance.
• Clean the  area around the oil fill tube (A, Figure 12).  Remove the  dip
stick (B) from the oil fill tube  and wipe the dip stick with a clean rag.
• Insert  the dip stick (B) into the oil fill tube
B
Chute Deflector
Cable
Figure 11
Figure 3
Align chute rotator control handle so it  is facing forward and use a
wrench to tighten jam nut (B) against  chute rotator control handle
D
B
C
9/16”
(A).
Drift Cutter
Drift Cutter
Slide chute rotator control handle to the  right hand side.
(thread in or push down completely).
Remove and check the engine oil level  (C). Oil level should be between
FULL and ADD MARKS.  If necessary, add oil  to the oil fill tube.
A
B
Figure 1
Skid Shoe
• Replace and  fully secure the dip stick (B).
5   Install Drift Cutters
A
Remove the fuel cap (D, Figure 12).
Add clean, fresh, UNLEADED fuel with a  minimum of 87 octane,
leaving one inch of space from the  top of the tank for fuel expansion.
C
For Assembly You Will Need:
Utility knife  Tin Snips or Banding Cutter
Unleaded fuel  •  Pliers  Tire Pressure Gauge
Figure 12
Drift cutters (A, Figure 5) are  mounted to snowthrower auger housing
(C).  With a 1/2 wrench remove the hardware (B).  Install  drift cutters
(A) placing tab (D) into square hole  (E) and the removed hardware (B).
• Reinstall the  fuel cap (D).
D
11  Final Checks
• Reduce the  tire pressures to the pressures shown below.  Tires are
over-inflated for shipping purposes and must  be set to the correct
pressures for optimum performance.  Tire Pressure: 14 PSI
• Check control  lever cables (A, Figure 13).  Check the “Z” bend ends
(C) of the control cables (A) are  secured in the holes on the control
levers (B) as shown.  Check that the cables  (A) are not kinked and
have freedom of movement.  Check that the auger  cable, right side,
(A, Figure 13) is on top of  cable button (D) as show.
B
Figure 4
D
1/2” Combination Wrench or 1/2” Deep Socket & Ratchet
3/8” Combination Wrench or 3/8” Socket & Ratchet
9/16” Combination Wrench or 9/16” Socket & Ratchet
7/16” Combination Wrench
C
A
C
6
Connecting Shift Rod
A
C
Connect shift rod (A, Figure 6) to  shift lever (B) secure with lock
washer (C) and nut (D) with a 1/2” wrench  and a 7/16’ wrench to
prevent stud (E) from turning.
B
tems Included:
Operator’s Manual
A
Chute Rotator Control Handle
One (1) Jam Nut (thin), 3/8”, use  9/16” wrench
One (1) Nut, 3/8”, use 9/16” wrench
One (1) Lock Washer, 3/8”
Two (2) Carriage Bolts, 5/16” x 2-1/4, use  1/2” wrench
Two (2) Lock Nuts, 5/16, use, use  1/2” wrench
Figure 13
7   Chute and Rotator Assembly
E
Loosely secure the spout rotator brake cable  to the spout rotator rod with a zip tie.
B
Bring chute from pallet to the  left side of snowthrower.
• Remove special  nut (A, Figure 7)  and cover (B).
• Remove hair  pin (C) with a pliers and slide rod (D) forward  about 8
inches.
D
• To prevent  the chute deflector cable from contacting the tire, rotate the  chute all the way to the left and
secure cable to the left handle with  zip tie (see Figure 1).
■  Two (2) Lock Nuts, 3/8,  use, use 9/16” wrench
120V Power Cord ■  Three (3)  Zip Ties
Two (2) Keys ■  Two (2)  Extra Shear pins
Two (2) Extra Cotter pins
Figure 5
Adjust light and secure the light wire  to the handle with a zip tie.
B
F
E
12  Starting the Engine
• Slide the  chute base (A, Figure 8) onto the auger housing (B).
G
A
Slide chute support tube (E,  Figure 8) on to the carriage bolts (D).
Do Not tighten at this time.
Move chute rotator control handle (A, Figure  9) to the right hand side
of the machine.
Slide spout rotator rod (B, Figure 9)  into hex dash opening (D).  It may
be necessary to move chute rotator  handle (B) for rod to go into dash.
Insert hair pin (C, Figure  9 ) into spout rotator rod (D).
Install cover (B, Figure 7) and secure  with special nut (A).
Secure chute support tube (E,  Figure 8) to chute base securing with
lock nuts (C) using a 9/16 wrench.
C
1
-- Operator’s Manual
Turn the fuel valve (B, Figure 14)  to the ON position.
Insert the engine key (F)  into the engine key slot and push in fully.
Move the throttle lever (E) all the  way to the right,
to the FAST position.
Turn the choke knob (G) fully counter  clockwise if engine is cold.
(Do not choke a warm engine.)
Push the primer button (D) two  times if engine is cold.
(Do not prime a warm engine.)
Engine Mounted Electric Start: See Operator’s  Manual.
Manual Start: Pull starter handle (C)  rapidly to start the engine.
B
D
A
2
LockNut
-- 3/8
1 -- 3/8
1 -- 3/8
Nut
2 -- 5/16”
LockNut
JamNut  (thin)
D
C
E
A
1
-- Chute Rotator
Control Handle
1 -- 120V Power Cord
Figure 6
2
-- Carriage Bolt
1
--  3/8
Figure 14
LockWasher
3
--  Zip Tie
Do not allow the starter  handle to snap back—let the starter rope rewind slowly—while  keeping a firm grip
on the starter handle.
As the engine starts and  begins to operate evenly, turn the choke knob (G)  slowly clockwise to the RUN
position, and set the Throttle Lever to SLOW. If the  engine falters, turn the choke knob counter-clockwise
until the engine runs smoothly, and  let it run briefly before returning the choke  to the RUN position.
2
--  Cotter Pin
A
2
--  Shear Pin
2
-- Ignition Keys
B
D
1
Remove the Packaging Materials
B
D
A
C
NOTE:  Allow the engine to warm  up at SLOW throttle for a few minutes before operating  the snowthrower at full speed. The
engine will not develop full power until  it reaches operating temperature.  After warming up, always operate at  full throttle.
13  Check that Clean-Out Tool is attached to Snowthrower
E
B
Remove the straps or banding
and cardboard from the crate.
Remove the parts bag
C
B
D
D
C
(A, Figure 2) from inside the
chute (B).  Locate and remove the
manual packet (C).
E
14  Snowthrower and Adjustments
Always use a clean-out tool to clear  clogged discharge chute.  Never use use your hands.
D
A
C
B
A
Figure 7
Figure 8
Figure 9
Figure 2
• Read Operator’s  Manual.
B
TP 1000-4518-01-LW-S
Form No. 173xxxx-00
©
Briggs & Stratton.
Every effort has been made to  ensure that the information in this document is accurate and  current. However, we reserve the right to change, alter or otherwise improve  the product and this document at any time without prior  notice.
Product Specification
CategoriesSimplicity Snow Blower Manuals, Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 1 page
Document TypeOwner's Manual
LanguageEnglish
Product BrandSimplicity, Snow Blower
Document File TypePDF
Publishersimplicitymfg.com
Wikipedia's PageSimplicity Outdoor
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website