Simplicity 555 755 860 1693980 81 82 83 1694433 34 Series Snow Blower Owners Manual

Operation
FREE-WHEELING AND
TRACTION DRIVE LOCK
For easy turning when pushing the snowthrower, you
can disengage the traction drive at one or both wheels
by using the Traction Lock Pins (See Figures 11 & 12).
Klik-Pin In
OUTER Hole
1.
Turn the unit off, remove the Engine Key, and discon-
nect the spark plug wire.
2.
To DISENGAGE the traction drive lock, insert the
Traction Lock Pin through the outer hole in the axle.
(See Figure 11).
3.
To ENGAGE the traction drive lock, insert the pin
through the hub and axle (See Figure 12). If the hole
in the hub is not aligned with the inner hole in the
axle, push the snowthrower until the holes align and
install the Traction Lock Pin.
NOTE: When snowthrowing with the full width of the
auger, for best drive performance engage both wheels.
For easier turning when not using the full width of the
auger, engage one wheel and use the engaged side as
the snow contact side for the auger.
Figure 11.  Traction Drive Lock - Disengaged
AFTER EACH USE
Klik-Pin In
INNER Hole
Normal use of the snowthrower may result in a build-up
of packed snow in and around the starter cord housing
and around engine controls. Heat from the engine will
usually prevent the snow from freezing solid while the
unit is running, but after the engine is shut down, some
snow may continue melting from engine heat, and later
freeze around some moving parts as the unit cools.
After each period of use, follow these steps to prevent
freeze-up caused by ice formation in and around the
engine controls and external parts.
1.
Before shutting off the engine, pull the starter rope
out 2 - 3 times, and allow it to rewind slowly. This will
help clear packed snow from the starter cord area.
Allow the engine to run for several minutes.
Figure 12.  Traction Drive Lock - Engaged
2.
3.
4.
Stop the engine by moving the Throttle Lever (See
Figure 8) down, or by pulling out the Engine Key.
WARNING
Disconnect the spark plug wire, and position it away
from the spark plug.
Never store snowthrower, with gasoline in engine
or fuel tank, in a heated shelter or in enclosed,
poorly ventilated enclosures. Gasoline fumes may
reach an open flame, spark or pilot light (such as
a furnace, water heater, clothes dryer, etc.) and
cause an explosion.
Brush snow and ice from the snowthrower. Be sure to
clear engine and snowthrower controls, discharge
chute, worm and chute rod gears, clutch rod areas,
and anywhere else snow has accumulated.
5.
6.
Always remove the Engine Key and store in a safe
place to prevent unauthorized use.
Handle gasoline carefully. It is highly flammable
and careless use can result in serious fire
damage to people and property.
If the snowthrower is kept in a cold shelter, fill the fuel
tank to prevent condensation. Do not store near
sparks or flame.
Drain fuel into an approved container outdoors
away from open flame or sparks.
Note: The Engine Owner’s Manual contains further infor-
mation on preventing ice formation and freeze-up.
16
Product Specification
CategoriesSimplicity Snow Blower Manuals, Snow Blower Manuals
Tags, , , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 34 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandSimplicity, Snow Blower
Document File TypePDF
Publishersimplicitymfg.com
Wikipedia's PageSimplicity Outdoor
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website