Simplicity 860 960 1693984 1693985 1694242 1694435 1694439 Large Frame Snow Blower Owners Manual

Controls
GROUND SPEED CONTROLS
B
A
D
C
A.  Speed Selector - This lever (A, Figures 2 & 3) is
used to set the ground speed of the snowthrower.
The snowthrower has five forward speeds, 1–5, and
two reverse speeds, 1–2. No neutral position or gate
is required, since the traction drive design automati-
cally provides "neutral" (no forward or reverse move-
ment), whenever the Drive Control is released.
B.  Traction & Free Hand™ Control - This control
engages the traction drive as the lever (B, Figures 2
&
3) is depressed, and disengages the traction drive
when the lever is released. When both levers are
depressed the Free Hand™ control is activated.  This
allows the auger control to be released yet the auger
remains engaged until the traction Free Hand™ is
released.  NOTE: Changing ground speeds must only
be done while the Drive Control is in the disengaged
(fully released) position.
Figure 2.  Operator's Control Position
A.  Speed Selector
B.  Traction Control
C. Auger Control
D. Chute Direction Control
AUGER CONTROL
C.  Auger Control - The Auger Control clutch lever (C
Figures 2 & 3), engages the auger drive when the
lever is depressed and disengages the auger drive
when the lever is released (unless Traction Free
Hand™ control is also depressed-see above).
C
D
B
A
F
DEFLECTOR CONTROLS
E
D.  Chute Direction Control - The Chute Direction
Control (D, Figures 2 & 3), allows the discharge chute
to be rotated to throw snow in the desired direction.
Snow may be thrown at any angle from straight left,
to straight forward, to straight right.
E.  Chute Deflector - Controls the distance snow is
thrown. Tilting the Chute Deflector (E, Figures 2 & 3)
UP provides a higher stream and greater distance,
while tilting the deflector DOWN provides a lower
stream and less distance.
H
F.  Chute Deflector Knob - This knob (F, Figures 2 & 3)
allows the discharge Chute Deflector (E, Figures 2 &
G
3)
to be locked in the desired tilt position.
Figure 3.  Snowthrower Controls
A.  Speed Selector                 E. Chute Deflector
B.  Traction Drive Control     F.  Chute Deflector Knob
SCRAPER HEIGHT
G.  Scraper Bar Height Control - The Skid Shoes (G,
Figure 3) control the height the scraper bar (located
at the bottom of the auger housing). The scraper bar
allows smooth surfaces (such as concrete or asphalt
driveways) to be scraped clean of snow. On surfaces
such as gravel, the scraper bar should be adjusted
higher — so that it will not pick up gravel or debris.
C.  Auger Control
D.  Chute Control
G. Skid Shoes
H. Traction Lock Pins
TRACTION LOCK CONTROL
H.  Traction Lock Pins - The traction drive to each
wheel can be locked and unlocked with the Traction
Lock Pins (H, Figure 3) to permit the unit to “free-
wheel,” allowing easier manual handling and transport
of the snowthrower.
11
Product Specification
CategoriesSimplicity Snow Blower Manuals, Snow Blower Manuals
Tags, , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandSimplicity, Snow Blower
Document File TypePDF
Publishersimplicitymfg.com
Wikipedia's PageSimplicity Outdoor
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website