Operation
Transporting
Daily Storage
1.
Disengage the electric clutch and then raise the
snowthrower.
1. Run the snowthrower a few minutes after blowing
snow to prevent freeze-up of auger.
2.
3.
Adjust ground speed according to surface conditions.
2. Allow tractor engine to cool before storing in any
enclosure.
Select a low ground speed when transporting on a
slippery surface.
Off-Season Storage
Engine & Ground Speed Selection
Always run the engine at full throttle.
WARNING
To prevent an explosion or fire, never store the
tractor with fuel in the tank inside a building where
an ignition source is present.
Normally, a low ground speed is best for throwing snow.
The deeper or heavier the snow, the slower the recom-
mended ground speed.
Starting & Stopping
1.
2.
Remove snowthrower from the tractor. Hitch can
remain installed if other attachments are to be used.
1.
Start the tractor engine. Set engine throttle at full
speed.
Use water pressure or a brush to thoroughly clean
the housing.
2.
3.
Lower the snowthrower.
Engage the electric clutch switch. Snowthrower auger
should rotate. Disengage the electric clutch switch.
snowthrower auger should stop.
3. Paint, or lightly coat with oil, any area where paint
has been worn or chipped away.
4.
5.
Lubricate the snowthrower.
4.
5.
Select the proper ground speed.
Store the snowthrower and hitch in a dry place.
To stop the tractor, depress the clutch/brake pedal.
To stop the snowthrower, disengage the electric
clutch. Before leaving the seat, stop the engine, dis-
engage the electric clutch, set the parking brake,
remove the key, and wait for all moving parts to stop.
Snow Removal Suggestions
•
•
•
•
•
Determine the best snow removal pattern before
beginning.
Wind direction is an important factor to consider.
Rotate the spout to discharge snow downwind.
Plan the pattern so that you avoid throwing snow on
cleared areas and on yourself as you are operating.
WARNING
If auger does not start and stop when
When land contour permits, it is best to travel in the
longest direction to minimize turning.
engaging/disengaging electric clutch, see your
authorized dealer. Under no circumstances should
you attempt to defeat the safety system.
In very deep or heavy snow, it may be necessary to
make the first pass with snowthrower partially raised,
backing up every few feet to clear the snow left on
the surface. Also, it may be necessary to slice off less
than the full width of the auger or reduce ground
speed.
WARNING
If the auger stalls or the chute plugs, DISENGAGE
THE ELECTRIC CLUTCH, STOP THE ENGINE AND
REMOVE THE KEY. SET THE PARKING BRAKE.
WAIT FOR MOVING PARTS TO STOP. Remove the
foreign object or clear the spout with a piece of
wood before restarting the engine. Never place
hands into auger housing or spout to clear
jammed object. Auger may rotate when object is
removed.
•
If snow stops flowing freely from the spout, back
away until the snowthrower clears itself.
CAUTION
Always raise the snowthrower before turning or
backing up, to prevent damage to the unit.
8
| Categories | Agco Allis Snow Blower Manuals, Massey Ferguson Snow Blower Manuals, Simplicity Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Agco Allis 1694404, Agco Allis 2000, Agco Allis 2900, Agco Allis 47, Massey Ferguson 1694404, Massey Ferguson 2000, Massey Ferguson 2900, Massey Ferguson 47, Simplicity 1694404, Simplicity 2000, Simplicity 2900, Simplicity 47 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Simplicity, Snow Blower |
| Document File Type | |
| Publisher | simplicitymfg.com |
| Wikipedia's Page | Simplicity Outdoor |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)