Toro Greensmaster 3050 3100 Specifications Briggs Stratton Vanguard V Twin Cylinder Specs

Greensmaster® 3050 & 3100 Specifications* (continued)
8 BLADE DPA CUTTING UNITS, 04610
11 BLADE DPA CUTTING UNITS, 04611
TRACTOR
These cutting units will mount on any Toro riding Greensmaster.
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062-.297" (1.6-
7.5 mm). With high HOC kit, range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.
HEIGHT OF CUT
(HOC) RANGE
Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat
treated to RC 48-54 hardness. The reel is ground for diameter and concentricity, and backgrind.
REEL WELDMENT
Two double row, self-aligning ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft with lock nut. Multiple seal barriers on
both sides of bearing for added protection. Reel position maintained by a wave washer with no adjusting nut.
REEL BEARINGS
MAINTENANCE
No grease zerks, sealed bearing design eliminates daily maintenance.
The reel weldment shaft is a 1.375" (35 mm) diameter tube with drive inserts permanently pressed in both ends. A replaceable floating
coupler with an internal eight tooth spline is factory installed on the right end, and held in place by a snap ring. The floating coupler
may be moved to the other end when the cutting unit is used on the GR3250-D front right position.
REEL DRIVE
FRAME
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.
Aggresiveness stays constant throughout the life of the reel. Patented design.
AGGRESSIVENESS
Replaceable single edged, high carbon steel bedknife austempered to RC 48-55, fastened to a machined cast iron bedbar with
13 screws. Tournament bedknife is standard.
BEDKNIFE
Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm)  bedknife movement for
each position.
BEDKNIFE
ADJUSTMENT
Front: Aluminum Wiehle, 2.5" (6.4 cm) diameter with sealed bearings and through-shaft. Option between full, narrow-spaced and
®
wide-spaced roller.
Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.
FRONT & REAR
ROLLERS
GRASS SHIELD
TOTAL WEIGHT
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.
8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller.
11-blade: 75 lbs. (34.1 kg) with aluminum Wiehle Roller.
DPA CUTTING UNIT OPTIONS
Part No.
93-4262
94-4263
93-4264
94-6392
63-8600
Description
Height of Cut Range (REC)
.062-.188" (1.6-4.8 mm)
.125-.375" (3.2-9.5 mm)
.188-1.00" (4.8-25.4 mm)
.312-1.00" (7.9-25.4 mm)
.375-1.00" (9.5-25.4 mm)
Micro-Cut Bedknife
Tournament Bedknife
Lo-Cut Bedknife (1/8)
Hi-Cut Bedknife
SERVICE BEDKNIVES
Fairway Bedknife
FULL ROLLER
NARROW-SPACED WIEHLE
WIDE-SPACED WIEHLE
Model 04625. Set of three (3) 2.5" +/-.03" (6.35 cm) diameter, with sealed bearings and through-shaft (steel tube).
Model 04626. Set of three (3) 2.5" +/-.03" (6.35 cm) diameter, .20" +/-.03" spacing with sealed bearings and through-shaft (aluminum).
Model 04627. Set of three (3) 2.5" +/-.03" (6.35 cm) diameter, .93" +/-.03" spacing with sealed bearings and through-shaft (aluminum).
Model 04628. Set of one (includes machined solid steel Front Narrow Wiehle Roller & solid steel Full Rear Roller).
SOLID STEEL ROLLERS
Includes a set of three (3) grooming reels, 2.375" (6.03 cm) diameter, .028" (.71 mm) thick heat treated spring steel, operating at 3,000
RPM. Powered by a six (6) rib Poly-V-Belt.
Model 04630. Kit contains three for GR3050/3100/3150.
GROOMER
Model 04631. Kit contains three for GR3250-D.
POWERED REAR
ROLLER BRUSH
Model 04640. Includes three brush assemblies. Fits GR3050/3100/3150.
Model 04641. Includes three brush assemblies. Fits GR3250-D.
P/N 108-6468. One front roller scraper (narrow-spaced Wiehle).
P/N 110-3961. One front roller scraper (wide-spaced Wiehle).
P/N 110-3962. One front roller scraper (full roller).
P/N 110-3963. One front roller scraper w/brush (narrow-spaced Wiehle).
P/N 110-3964. One front roller scraper w/brush (wide-spaced Wiehle).
P/N 110-3965. One front roller scraper w/brush (full roller).
P/N 110-3966. One front roller scraper w/poly comb (narrow-spaced Wiehle).
P/N 110-3967. One front roller scraper w/poly comb (wide-spaced Wiehle).
P/N 110-3968. One front roller scraper w/poly comb (full roller).
P/N 108-6473. One rear roller scraper.
ROLLER
SCRAPER KITS
HIGH HEIGHT OF CUT KIT
P/N 106-4699. For one cutting unit.
P/N 106-2626. One reel weld assembly.
P/N 107-9522. One reel weld assembly.
P/N 106-2616. One brush.
5
8
BLADE HEAVY DUTY REEL
BLADE HEAVY DUTY REEL
GROOMER BRUSH ASSY.
* Specifications and design subject to change without notice.
The Greensmaster 3050 & 3100 are manufactured in
Tomah, WI  ISO 9002 Certified Plant.
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 2 pages
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website