Toro Greensmaster 3150 Q Specifications Specs

Greensmaster   3150-Q  Specifications*
®
GREENSMASTER 3150-Q, MODEL 04357
18 hp (13 4 kW) Briggs & Stratton® gasoline engine, governed to 2850 rpm high idle, 1650 rpm low idle  Air cooled, 34 8 cu  in  (570 cc)
7 gallon (26 5 liter) capacity; unleaded gasoline
ENGINE
FUEL CAPACITY
TRACTION DRIVE
2 or 3WD w/ROPS, hydrostatic piston pump closed loop system  Foot pedal forward and reverse; infinitely variable
Forward-mowing speed is variable from 2-5 mph (3 2-8 km/h), adjusted by stop on pedal mechanism  Mow speed setting does not
affect transport speed  Maximum Greensmaster 3150-Q transport speed is 8 8 mph (14 4 km/h), may be reduced by adjusting stop
in footrest pan without affecting mow speeds  Reverse is 2 5 mph (4 0 km/h) maximum
GROUND SPEED
TURF COMPACTION
IMPLEMENT DRIVE
STEERING
8-10 psi (dependent on tire pressure) with operator and cutting units down
Single gear pump, mono valve block, series reel drive to 3 reel motors
Power steering  Adjustable steering wheel tilt and a 5-position steering arm tilt
12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps
draw  16 amp alternator  Ignition switch/key  Seat switch  Harness terminals and fuse slot available for optional lights installation  
ELECTRICAL FEATURES
CONTROLS/GAUGES
Raise/lower-mow lever (joystick)  Functional control lever (neutral, mow, transport)  Foot operated traction drive and brakes  Hour
meter  Hand operated throttle and choke  Mechanical engine speed control  
TIRES/WHEELS/
PRESSURE
Three tires: 18 x 9 50-8, 2-ply pneumatic, tubeless, demountable and interchangeable with smooth tread   
Tire pressure: 8-12 psi (55-83 kPa)  Optional Traction Tire (2-ply): P/N 231-127
BRAKES
HYDRAULIC OIL
LEAK DETECTION
SOUND LEVEL
Two 6" (15 2 cm) drum type
7 5 gallon (28 4 liter) tank with internal baffle  1 0 gallon (3 8 liter) auxiliary tank
Equipped with Turf Guardian™ leak detection system
81 dB(A) at operator’s ear under normal conditions
Wheel Tread: 49 5" (149 9 cm), Wheel Base: 47" (119 cm), Length: 90" (229 cm), Width: 69 75" (177 cm) w/reels, Height: 48 5" (123
cm), Weight (no reels): 970 lbs  (440 kg)
OVERALL DIMENSIONS
WIDTH OF CUT
REEL SPEED
59" (150 cm)
Approximately 1975 RPM at 2850 engine RPM  Adjustable
Standard equipment
BACKLAPPING
Cutting units are completely free-floating, each attaching to the tractor by direct pull links and lifted by a centered lift arm  Baskets
are supported by carrier frames that are ground following  Cutting unit floatation is unaffected by basket content  Grass baskets are
all interchangeable and accessible from the front of the machine
CUTTING UNIT
SUSPENSION
OPTIONAL ACCESSORIES
WARRANTY
3WD kit w/ROPS, traction tire, thatching reels, spiker, tri-roller, turf evaluator
Two-year limited warranty  Refer to the Operator’s Manual for further details  Briggs & Stratton provides a two-year commercial
engine, and a lifetime Magnetron® ignition warranty
8 BLADE DPA CUTTING UNITS, 04610
11-BLADE DPA CUTTING UNITS, 04611   14-BLADE CUTTING UNITS, 04616**
TRACTOR
These cutting units will mount on any Toro riding Greensmaster
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws  Bench HOC range is  
062"- 297" (1 6-7 5 mm)  With high HOC kit, range is  285-1" (7 3-25 4 mm)  Effective HOC may vary depending on turf  
conditions and bedknife installed
HEIGHT OF CUT
(HOC) RANGE
Reels are 5" (13 cm) in diameter, 21" (53 3 cm) in length  High carbon steel blades are welded to 5 stamped steel spiders, and heat
treated to RC 48-54 hardness  The reel is ground for diameter and concentricity, and backgrind
REEL WELDMENT
Two double row, self-aligning ball bearings, 30 +/- 1 mm inside diameter slip fit onto reel shaft with lock nut  Multiple seal barriers
on both sides of bearing for added protection  Reel position maintained by a wave washer with no adjusting nut  
REEL BEARINGS
MAINTENANCE
No grease zerks, sealed bearing design eliminates daily maintenance
The reel weldment shaft is a 1 375" (35 mm) diameter tube with drive inserts permanently pressed in both ends  A replaceable
floating coupler with an internal eight tooth spline is factory installed on the right end, and held in place by a snap ring  The floating
coupler may be moved to the other end when the cutting unit is used on the GR3250-D front right position
REEL DRIVE
FRAME
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates
Aggressiveness stays constant throughout the life of the reel  Patented design
AGGRESSIVENESS
Replaceable single edged, high carbon steel bedknife austempered to RC 48-55, fastened to a machined cast iron bedbar with 13 screws  
TM
Tournament Bedknife is standard on 8-blade & 11-blade cutting units  EdgeMax   Microcut Bedknife is standard on 14-blade cutting unit  
BEDKNIFE
BEDKNIFE
ADjUSTMENT
Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to  0007" ( 018 mm)  bedknife movement for  
each position  
Front: Aluminum Wiehle , 2 5" (6 4 cm) diameter with sealed bearings and through-shaft  Option between full, narrow-spaced and
®
wide-spaced roller   
Rear: Steel full, 2" (5 1 cm) diameter with sealed bearings and through-shaft
FRONT & REAR
ROLLERS
GRASS SHIELD
TOTAL WEIGHT
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions
8-blade: 72 lbs  (32 7 kg) with aluminum Wiehle Roller   
11-blade: 75 lbs  (34 1 kg) with aluminum Wiehle Roller
*Specifications and design subject to change without notice
**Available Winter/Spring 2010, see your distributor for details
The Greensmaster 3150-Q is manufactured in
Tomah, WI  ISO 9002 Certified Plant
45
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 2 pages
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website