Toro Groundsmaster 300 Series 4WD Specifications

Groundsmaster
®
300 Series  Accessories Specifications*
FULL FLOTATION CUTTING UNITS
72" SIDE DISCHARGE, MODEL
30722 &
GUARDIAN  72" RECYCLER  ,
®                                                  ®
72" REAR DISCHARGE, MODEL
30710
MODEL 30716
72" (183 cm) width of cut, three blade, mounted rotary.
Side or rear discharge respectively.
72" (183 cm) width of cut, three blade, front mounted rotary.
Recycling with no discharge.
TYPE
MOWING RATE [1]
Mows up to 4.0 acres/h (1.6 hectares/h) at 5.5 mph (8.9 km/h).
Deck offset to the right from centerline: 18" (46 cm). Deck trim
width from outside of standard traction tire to trim side - right:
23" (58 cm). Uncut circle - right: 15" (38 cm). Uncut circle with
use of wheel brakes: 0". Rear discharge trims both sides.
Deck offset to right from centerline: 7" (18 cm). Deck trim width from
outside of standard tire to trim side - right: 22" (56 cm).
Uncut circle - right: 24" (61 cm). Uncut circle with use of wheel
brakes: 0". Guardian 72" Recycler trims on both sides.
TRIMMING ABILITY
1-4" (2.5-10 cm) adjustable front and rear in .5" (13 mm)
increments with spacers on the caster shafts.
1.5-4.5" (3.5-11 cm) adjustable front and rear in .5" (13 mm)
increments with spacers on the caster shafts. 1.5" (3.5 cm)
and 2" (5 cm) height of cut not recommended under severe
cutting conditions.
HEIGHT OF CUT
CONSTRUCTION
Model 30722: 11-gauge steel, 6" (15 cm) deep with 2" (5 cm)
step. Reinforced with 3.5" (8.9 cm) x 7-gauge channel.
Model 30710: 11-gauge steel, 4" (10 cm) deep housing.
Reinforced with 3.5" x 7" gauge channel.
12-gauge steel, 5.5" (14 cm) deep, welded
construction reinforced with 10-gauge
channels and plates.
SPINDLE
ASSEMBLY
Ductile cast iron spindle housing. Dual greaseable tapered roller bearings. 1.25" (3.2 cm) diameter solid cold finished steel spindle shaft.
Splined connection between spindle shaft and pulley. Welded blade retainer plus anti-scalp cups.
Isolation mounted PTO driven gearbox with 1.26:1 spiral bevel
gears. “B” hex section belts to spindles. 1.25" (3.2 cm)
diameter spindle shafts, protected by rugged conical spindle
housing, turn on two greaseable tapered roller bearings
(greaseable from top of deck). A positive splined connection
attaches pulleys to spindle shafts for high torque capacity.
Isolation mounted PTO driven gearbox with 1.26:1 spiral bevel
gears. Single “BB” section hex belt to spindles. Self-tensioning
idler pulleys. 1.25" (3.2 cm) diameter spindle shafts turn on two
greaseable tapered roller bearings (greaseable from top of deck).
A positive splined connection attaches pulleys to spindle shafts
for high torque capacity.
CUTTER DRIVE
BLADES
Three 25" (64 cm) long, .25" (6 mm) thick, heat-treated steel,
suction-lift blades.
Three 25" (64 cm) long, .25" (6 mm) thick, heat-treated steel,
Recycler blades.
Two front and rear caster tires consist of hard rubber and roller bearings. Deck counterbalanced by two torsion springs. Foam Filled
Castor Wheel, 10" (25 cm) =P/N 93-5973 (two required) or 8" (20 cm) =P/N 93-5974 (two required).
SUSPENSION &
CASTER WHEELS
Front Tires
Rear Tires
Models 30722 & 30710
Model 30716
10.00" x 3.25" (25 x 8.3 cm)
10.00" x 3.25" (25 x 8.3 cm)
6.25" x 3.00" (16 x 7.6 cm)
8.00" x 3.50" (20 x 8.9 cm)
Model 30710: One front center anti-scalp left and right skids.
Model 30722: One front center and two rear center
anti-scalp rollers and RH skid. All rollers are 2-position adjustable.
Anti-scalp cup located on each blade. Three anti-scalp rollers.
Adjustable skids.
ANTI-SCALP
FEATURES
Quick-release covers. No tools required to remove.
Quick-release, high impact plastic covers. No tools required to
remove.
DECK COVERS
WEIGHT
Model 30722: 400 lbs. (181 kg).
Model 30710: 415 lbs. (188 kg)
465 lbs. (211 kg)
Model 30722: 85.5". (217 cm).
Model 30710: 76" (193 cm)
75" (191 cm)
WIDTH
ADDITIONAL
COUNTERBALANCE
WEIGHT [2]
Model 30626: 70 lbs. (32 kg)
Model 30789: 105 lbs. (48 kg)
Model 30626: 70 lbs. (32 kg)
Model 30789: 105 lbs. (48 kg)
CERTIFICATION
Certified to meet the American National Standard Institute’s (ANSI) specifications, B71.4-1999 and applicable Federal and State regulations based thereon.
* Specifications and design subject to change without notice.
[1] Mowing rate is dependent on conditions.
[2] Different rear counter weights are required with traction unit models 30626 and 30789 depending upon which deck or attachment is being used to meet ANSI.
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 3 pages
Document TypeSpecifications
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website