Rake-O-Vac Specifications*
®
RAKE-O-VAC ENGINE DRIVE, MODEL 07050
Kohler
®
Command Series CH235, 22 hp (16.4 kW) @ 3600 rpm, 4 cycle, air-cooled, V-twin cylinders, horizontal crankshaft with a 5.5"
(14 cm) dry centrifugal clutch. Compression ratio: 8.5:1. Overhead placement valves; intake, forged high carbon steel, exhaust Stellite
faced. Hydraulic valve lifters. Full pressure 4 pint (2.3 liter) with filter, oil capacity. 12 volt, 15 amp alternator with solid state
regulator/rectifier. Solid state electronic ignition system with electronically controlled spark advance. Tri-phase design with screen pre-
cleaner, replaceable filter cartridge and dump valve.
®
POWER SUPPLY
Centrifugal type housing, double inlet. Four alloy steel blades, 16" (41 cm) wide x 231/ " (59 cm) diameter, 3/ " (4.8 mm) thick. High
2 2
(1645 cm ).
FAN IMPELLER
DRIVE
4
16
tensile, 9/16" (4 cm) stress-proof steel shaft mounted in self-aligning sealed ball bearings. Blower discharge area: 255 in
Banded double. B-80 drive belt direct from drive shaft to fan impeller drive shaft. Fan impeller runs at 1580 rpm [tip speed 9,720 ft/min.
(2963 m/min.)] at 3250 engine rpm.
Twin construction for uniform air distribution; 4.5" (11.4 cm) deep x 63" (160 cm) wide. Inlet area: 283 in (1826 cm ). Variable position,
2 2
front weighted rubber flap.
FAN HOOD
Belted-double B-53 drive belt from engine to jack shaft. Banded (4) 3V cross section belt, from jack shaft to flex tip reel. Flex tip reel
runs at 275 rpm [tip speed 1,355 ft./min. (413 m/min.)] at 3250 engine rpm.
REEL/BRUSH DRIVE
MAIN FRAME
All welded, structural, rectangular, 2" x 4" (5 cm x 10 cm) and 4" x 4" (10 cm x 10 cm), 11 gauge, steel tubing.
High flotation type I-1 rib tread, 11L-14SL, 6 ply rating, tubeless construction mounted on 8" (20 cm) x 14" (36 cm) wheel with six bolt
attachment. Inflation pressure 28 psi (1.9 bar).
WHEELS AND TIRES
5.75 cu. yd. (4.4 m ) volume; 18 gauge top section with 16 gauge bottom section - rib reinforced; full width, self-cleaning,
3
semi-automatic dumping.
HOPPER
HITCH Pin type, 3/4" (1.9 cm) diameter; adjustable vertical height for tractor hitches from 71/4" (18.4 cm) to 171/4" (43.8 cm) height.
Forward sweeping, 6 rows of teeth, all steel construction with replaceable 3/ " (4.8 mm) extruded nylon teeth; each row containing 11
16
individually spring loaded flexible sets, 552 total teeth, 183/ " (48 cm) diameter reel, 61" (155 cm) wide, 11/8" (2.9 cm) diameter shaft set
FLEX TIP REEL
4
in self aligning sealed bearings. Reel supported by adjustable counterbalance springs and adjustable-gauge wheels. Gauge wheels
aluminum construction with non-scuffing rubber tires operating on greaseable ball bearings; infinitely adjustable vertically.
Width
85.5" (217 cm)
Height
79.5" (202 cm)
Length
13'3" (4.0 m)
DIMENSIONS
WEIGHT
2,160 lbs. (980 kg)
WARRANTY
Two year limited warranty. Refer to the Operator’s Manual for further details.
OPTIONAL EQUIPMENT
HARD SURFACE
BRUSH
Forward sweeping continuous, polypropylene bristle, floating action provided by spring counterbalance and gauge wheel height
adjustment.
MODEL 07162
Brush speed: 275 rpm [tip speed 1,370 ft./min. (417 m/min.)] at 3200 engine rpm.
Forward cutting all steel construction. 16 hardened, 12 gauge steel blades spaced 33/4" (9.5 cm), 16" (41 cm) O.D. x 61" (155 cm) wide.
Kit includes self-aligning bearings, both drive sprocket (18 tooth) and reel sprocket (36 tooth), heavy duty #60 roller chain and idler;
reel fitted with shear-bolt safety impact break-away at 36 tooth sprocket; [170 lbs. (77 kg)]. Reel - 532 rpm [tip speed 2,228 ft/min.
(679 m/min.)] at 3250 engine rpm.
THATCHING REEL
MODEL 07178
Reel speed: 532 rpm [tip speed 2,228 ft/min. (679 m/min.)] at 3250 rpm.
Description is the same as it reads above following: “Flex Tip Reel”.
FLEX TIP REEL KIT
MODEL 07164
* Specifications and design subject to change without notice. Products depicted in this literature are for
demonstration purposes only. Actual products offered for sale may vary in design, required attachments and
safety features. Consult your local Toro Distributor. “Stellite” is a trademark of Stoody Deloro Stellite, Inc.
The Rake-O-Vac is manufactured
in Tomah, WI ISO 9002 Certified Plant.
Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
---|---|
Tags | Toro Rake O-Vac 3600 |
Download File |
|
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)