SECTION 4: OPERATING YOUR SNOW THROWER
Before Starting
•
•
•
•
The electric starter is equipped with a grounded
three-wire power cord and plug, and is designed to
operate on 120 volt AC household current.
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
If your home wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
If your home electrical system is grounded, but
a three-hole receptacle is not available, one should
be installed by a licensed electrician before using
the electric starter.
WARNING: Read, understand, and follow all
instructions and warnings on the machine and
in this manual before operating.
•
The spark plug wire was disconnected for safety.
Attach spark plug wire to spark plug before starting.
Gas and Oil Fill-Up
•
Check oil and gasoline level and add if necessary.
Follow related instructions in the separate engine
manual packed with your snow thrower.
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Never
fuel the machine indoors or while the engine is
hot or running. Extinguish cigarettes, cigars,
pipes and other sources of ignition.
•
If you have a grounded three-prong receptacle,
proceed as follows.
Move Choke Control to “Full” position.
Push Primer three (3) times, making sure to cover
vent hole when pushing.
Connect power cord to switch box on dash panel.
Plug the other end of power cord into a three-prong
120-volt, grounded, AC receptacle.
Push starter button to crank engine. As you crank
the engine, move choke lever to FULL choke
position.
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
When disconnecting the power cord, always unplug
from the three-prong receptacle first, and then from
the snow thrower.
•
•
•
•
•
To Start Engine
Insert ignition key into slot. Turn key to ON position.
Now follow the instructions below as it pertains to
your unit. See Figure 4 for location of controls.
•
•
Electric Starter(If Equipped)
WARNING: The electric starter must be
used with a properly grounded three-prong
receptacle at all times to avoid the possibility of
electric shock. Follow all instructions carefully
prior to operating the electric starter.
•
Recoil Starter
•
•
•
•
Move choke lever to FULL choke position (cold
engine start).
If engine is warm, place choke in OFF position
instead of FULL.
Push primer button two or three times for cold
engine start.
Press auger
control handle
to engage
auger
If engine is warm, push primer button only once.
Recoil
NOTE: Always cover vent hole in primer button when
pushing. Additional priming may be necessary for first
start if temperature is below 15° F (-9° C).
Primer
Key
Starter
•
Grasp starter handle and pull rope out slowly, until
it pulls slightly harder. Let rope rewind slowly.
Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle.
Electric
•
Starter
Choke
Lever
(If Equipped)
Spark Plug Access
•
As engine warms up and begins to operate evenly,
rotate choke lever slowly to OFF position. If engine
falters, return to FULL choke, then slowly move to
OFF position.
Figure 4
7
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Yard Man Snow Blower Manuals |
|---|---|
| Tags | MTD 295, MTD 2B5, MTD E295, MTD E2B5, MTD Snow Blower Manual, Yard Man 295, Yard Man 2B5, Yard Man E295, Yard Man E2B5 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Yard-Man, 2B5, E295, E2B5, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)