MAINTENANCE & REPAIR INSTRUCTIONS
For Use with Single
Line ONLY
For Use with SplitLine™
or Single Line
Slotted
Holes
Loop
Fig. 21
Fig. 18
11. Wind the line in tight even layers in the direction indicated
on the inner reel.
NOTE: Failure to wind the line in the direction indicated will cause
the cutting attachment to operate incorrectly.
NOTE: SplitLine™ can only be used with the inner reel with the
slotted holes. Single line can be used on either type of
inner reel. Use Figure 18 to identify the inner reel you have.
NOTE: Always use the correct line length when installing
trimming line on the unit. The line may not release
properly if the line is too long.
12. Insert the ends of the line into the two holding slots (Fig. 22).
Loop
Holding Slots
Fig. 22
13.
Insert the ends of the line through the eyelets in the outer
spool and place inner reel with spring inside the outer spool
(Fig. 23). Push the inner reel and outer spool together. While
holding the inner reel and outer spool, grasp the ends and pull
firmly to release the line from the holding slots in the reel.
Fig. 19
Single Line Installation
Go To Step 8 for SplitLine™ Installation
6.
Take approximately 18 feet (5.4 m) of new trimming line, loop
it into two equal lengths. Insert each end of the line through
one of the two holes in the inner reel (Fig. 19). Pull the line
through the inner reel so that the loop is as small as possible.
7.
Wind the lines in tight even layers, onto the reel
(Fig. 20). Wind the line in the direction indicated on the
inner reel. Place your index finger between the two lines to
stop the lines from overlapping. Do not overlap the ends of
the line. Proceed to step 11.
Spring
Fig. 23
NOTE: The spring must be assembled on the inner reel before
reassembling the cutting attachment.
14.
Hold the inner reel in place and install the bump knob by
turning clockwise. Tighten securely.
INSTALLING A PREWOUND REEL
Fig. 20
1.
Hold the outer spool with one hand and unscrew the bump
knob counterclockwise (Fig. 15). Inspect the bolt inside the
bump knob to make sure it moves freely. Replace the bump
knob if damaged.
SplitLine™ Installation
8.
Take approximately 9 feet (2.7 m) of new trimming line.
Insert one end of the line through one of the two holes in
the inner reel (Fig. 21). Pull the line through the inner reel
until only about 4 inches is left out.
Insert the end of the line into the open hole in the inner reel
and pull the line tight to make the loop as small as possible
(Fig. 21).
2.
3.
4.
Remove the old inner reel from the outer spool (Fig. 16).
Remove the spring from the old inner reel (Fig. 16).
Place the spring in the new inner reel.
9.
NOTE: The spring must be assembled on the inner reel before
reassembling the cutting attachment.
5.
Insert the ends of the line through the eyelets in the outer
spool (Fig. 23).
10.
10
Before winding, split the line back about 6 inches.
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, Yard Man Lawn Mower Manuals |
|---|---|
| Tags | MTD YM70SS, Yard Man YM70SS |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower, YM70SS |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)