Checking the Interlock Switch
Operation
1.
Make sure traction and reel drive levers are in
Disengaged position.
Note: Engine will not start if traction lever is in
the engaged position.
2.
3.
4.
5.
Open the fuel shut-off valve on the engine.
Move the on/off switch to the On position.
Move the throttle control to the Fast position.
If safety interlock switches are disconnected
or damaged the machine could operate
unexpectedly causing personal injury.
Move the choke lever to the half-open position
when starting a cold engine. The choke may not be
required when starting a warm engine.
•
•
Do not tamper with the interlock switches.
Check the operation of the interlock
switches daily and replace any damaged
switches before operating the machine.
6.
Pull the recoil starter handle out until positive
engagement results, then pull it vigorously to start
the engine. Open the choke as engine warms up.
1.
Push kick stand down with foot and pull up on
handle support until kick stand has rotated forward,
over center (Figure 18).
Important: Do not pull recoil rope to its limit
or let go of starter handle when rope is pulled
out because rope may break or recoil assembly
may be damaged.
Stopping the Engine
1.
2.
3.
Move the traction and reel drive controls to the
Disengaged position, the throttle control to Slow,
and the on/off switch to Off.
Pull the molded spark plug wire off of the spark
plug to prevent the possibility of accidental starting
before storing machine.
Close the fuel shut-off valve before storing or
transporting mower in a vehicle.
Figure 18
Transport Operation
1.
2.
3.
Kick stand
Note: Do not run the mower engine while transporting
it in a transport trailer because damage can occur to
the mower.
Place traction lever into Engage position and engine
controls in starting position.
If optional transport wheels are not going to be
installed, proceed to step 4.
Attempt to start engine. Engine should not start.
If engine starts, the interlock switch needs service.
Correct problem before operating. Refer to
Servicing Interlock Switch.
1. Push kick stand down with foot and pull up on
handle support until kick stand has rotated forward,
over center.
4.
Carefully lift up on handle to release kick stand.
2.
3.
Install the transport wheels.
Starting and Stopping the
Engine
To release kickstand, pull up on handle and lower
rear of mower onto transport wheels.
4.
5.
Ensure traction and reel drive controls are in
Disengage position and start engine.
Note: For illustrations and descriptions of the controls
referenced in this section, refer to Controls , page 14.
Set throttle control to Slow, tip front of machine up
gradually engage traction drive and slowly increase
engine speed.
Starting the Engine
Note: Make sure spark plug wire is installed on spark
plug.
6. Adjust throttle to operate mower at desired ground
speed and transport mower to desired destination.
17
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro 04030, Toro 04031, Toro 04202, Toro 04206, Toro Greensmaster |
| Model Number | 04030, 04206, 04031, 04202 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 280000001-280999999 |
| Product Name | Toro Greensmaster Flex 18 Mower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Product Series | Toro Greensmaster - Flex Series |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)