FUEL HANDLING
Fuel mixture
Mixture
•
Always mix petrol and oil in a clean container intended for
petrol.
NOTE!
The machine is fitted with a two-stroke engine and must
always be run on a mixture of petrol and two-stroke oil. It is
important to measure the quantity of oil accurately, to ensure
the correct mixture ratio. Small discrepancies in the amount of
oil have a great bearing on the proportions of the fuel mixture
when mixing small amounts of fuel.
• Always start by filling half the quantity of petrol required.
Then add the entire oil quantity. Mix (shake) the fuel
mixture. Fill the remaining quantity of petrol.
• Mix (shake) the fuel mixture carefully before filling in the
machine‘s fuel tank.
!
WARNING!
Always provide good ventilation when
handling fuel.
• Do not mix more than max. one month’s supply of fuel.
•
If the machine is not used for a long period of time, the fuel
tank should be emptied and cleaned.
Petrol
!
NOTE!
WARNING!
The catalytic converter muffler gets very hot
during and after use. This also applies
during idling. Be aware of the fire hazard,
especially when handling the saw near
flammable substances or vapours.
Always use an oil-mixed
quality petrol (at least 90
octane). If your machine is
equipped with a catalytic
converter, (see “technical
data”) an unleaded, oil
mixed quality petrol
Fuelling
should always be used. A
leaded petrol will destroy
the catalytic converter
!
WARNING!
The following precautions reduce the risk
of fire:
•
The lowest
Do not smoke or place any sources of heat
in the vicinity of the fuel. Never refuel
when the engine is running. Always stop
the engine and let it cool for a few minutes
before refuelling. Open the fuel cap slowly
when fuelling so that any over pressure is
released slowly. Tighten the fuel cap
carefully after refuelling. Always move the
machine from the fuelling place before
starting.
recommended octane
rating is 90. If you run
the engine on a petrol
with a lower octane
rating than 90 so-called
“knocking“ can occur.
This leads to an
increased engine
temperature, which can
result in a serious engine
breakdown.
•
•
Clean around the fuel
cap. Contamination in
the tank can disrupt
operations.
•
When working at
continuous high revs a
higher octane rating is
recommended.
Ensure that the fuel is
well mixed by shaking the
container before filling
the tank.
Two-stroke oil
Min. 3 m
(10
ft)
•
•
•
For the best results use HUSQVARNA two-stroke oil,
which has been specially produced for clearing saws and
chain saws.
Mixing ratio 1:50 (2%).
If HUSQVARNA two-stroke oil is not available you can use
a high quality two-stroke oil intended for air cooled engines.
Contact your dealer when selecting an oil.
Gasolin
Benzin
Essence
Gasolina
Lit.
Oil • Öl
Huile • Aceite
Lit.
2% (1:50)
3% (1:33)
0,15
0,30
0,45
0,60
5
0,10
0,20
0,30
0,40
Mixing ratio: 1:33 (3%).
10
15
20
US
gallon
Never use two-stroke oil intended for water cooled outboard
motors, so-called outboard motor oil.
US
fl. oz.
2% (1:50)
2 1/2
3% (1:33)
3 3/4
1
2
1/2
5
6 1/2
12 7/8
9 3/4
19 1/4
•
Never use oil intended of four-stroke engines.
14
– English
| Categories | Chainsaw Manuals, Husqvarna Chainsaw Manuals |
|---|---|
| Tags | Husqvarna 225L, Husqvarna 227L, Husqvarna 232L, Husqvarna 240L |
| Model Year | 1999, 2000, 2001 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Product Brand | Husqvarna, Chainsaw |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)