IMPORTANT: STORE SNOWTHROWER
IN OPERATING POSITION ON ITS
WHEELS. TIPPING OR STORING UNIT
FORWARD ONTO FRONT HOUSING
MAY CAUSE HARD STARTING.
from cable adjuster and reposition Z fitting in a
higher or lower hole on adjuster to obtain proper
gap of 1/16”–1/8” between control bar bracket
and handle (Fig. 6). (Positioning cable end in a
lower hole decreases gap; positioning cable end
in a higher hole increases gap.) Reinstall spring
cover over cable adjuster. Reinstall upper cable
end into rear hole in control bar bracket (hole
with arrow) (Fig. 6).
Maintenance
4.
After extended use the drive belt may wear and
proper belt tension may not be maintained.
Improper belt tension causes belt slippage and
decreases the snowthrower’s performance under
a heavy load. Belt slippage may occur after 2–3
seasons of normal usage (10–15 hours). If drive
belt slips (continuous squealing noise) under
heavy load, increase belt tension by
NOTICE:
Maintenance, replacement or repair
of the emission control devices and
systems may be performed by any
nonroad engine repair establishment
or individual. However, to obtain no
charge repairs under the terms and
provisions of the Toro warranty
statement, any service or emission
control part repair or replacement
must be performed by an
repositioning upper cable end into forward hole
in control bar bracket (Fig. 6). Readjust cable
(see steps 2–3).
Authorized Toro Service Dealer.
IMPORTANT: Unnecessary use of forward
adjusting hole in control bar bracket reduces
drive belt life. Occasional belt slippage
(squealing) may occur in extremely wet
conditions due to moisture in drive system. To
remove moisture, start rotor and operate under
no load for 30 seconds. Once moisture is
removed, belt should not slip.
General Maintenance
Normally, the only maintenance required is cleaning
the unit and tightening nuts, bolts, and screws.
However, the scraper, drive belt, rotor blades, and
spark plug should be checked once a year.
Adjusting Control Bar
Draining Gasoline
Periodically check control bar for proper adjustment.
1.
2.
Turn ignition key to OFF.
1.
2.
Stop engine. Remove key from switch.
CHECK ADJUSTMENT (Fig. 9)—Move
control bar back toward handle until slack in
cable is removed. Gap between control bar
bracket and handle should be approximately
Remove cap from fuel tank and use a pump type
syphon to drain fuel into a clean gas can.
Note:
This is the only procedure
recommended for draining fuel.
1/16”–1/8”.
If cable is too loose or too tight,
proceed to step 3 for adjustment procedure.
Replacing Scraper (Fig. 11-12)
Note:
The control cable must always have
slack in it when in the disengaged
position.
Before each season, inspect scraper for wear. If
thickness of bottom of scraper is less than 1/16”
3.
Unhook upper cable end from hole in control bar
bracket (Fig. 6). Slide spring cover up cable to
expose cable adjuster (Fig. 10). Unhook Z fitting
(1.6
mm), replace scraper (Fig. 11).
1.
Turn ignition key to OFF.
8
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38430, Toro 38435, Toro CCR 3000 |
| Model Number | 38430, 38435 |
| Model Year | 1999 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 9900001 - 9999999 |
| Product Name | Toro CCR 3000 38435 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 2000/3000/3600, Single Stage, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Suzuki |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | 47PT7-5 |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(3 votes, average: 3.33 out of 5)
Lawn and Garden readers have rated Toro CCR 3000 GTS 38430 38435 20 Inch Single Stage Snow Blower Operators Manual 1999 3.3 out of 5.0 based on 3 product reviews. I have just downloaded the manual and I have no idea how to access it so I can use it. When I click on the file to open it, It takes me back to the web page so I can download it again. This was my first attempt. Slow learning curve... Hope I can figure out how to use your pages....
I looking for new scrapers for my TORO snow blower model #38430 CCR 3000 GTS 5.0 thanks
If this is the manual for my snowblower, then great site.