2.
Drain gasoline from fuel tank; refer to Draining
Gasoline, page 8.
Replacing Spark Plug
(Fig. 15-17)
3.
4.
Tip snowthrower forward onto front housing.
Before each snow season, check the spark plug. If
electrodes in center of plug are dark or have
deteriorated, install a new plug. Use an NGK
BPMR4A spark plug and set gap at .032” (.81 mm).
Remove (3) carriage bolts and locknuts holding
scraper in place (Fig. 12). Remove scraper by
sliding it to right and down.
1.
REMOVE CONTROL PANEL
(Fig. 15)—Remove (3) capscrews securing
control panel to housing. Remove ignition key
and lift off panel, allowing it to hang on recoil
rope.
5.
Install new scraper to housing using carriage
bolts and nuts.
2.
REMOVE SPARK PLUG (Fig. 16)—Pull wire
off spark plug and remove plug. Examine the
plug and replace if cracked, fouled or dirty. DO
NOT SANDBLAST, SCRAPE OR CLEAN
SPARK PLUG BECAUSE DIRT MAY
RELEASE AND FALL INTO CYLINDER
CAUSING ENGINE DAMAGE.
Replacing Drive Belt
(Fig. 13-14)
Inspect drive belt before each season. If ribs on inside
of belt are damaged or belt is worn, replacement is
necessary.
3.
INSTALL SPARK PLUG—Set air gap (Fig. 17)
between electrodes at .032” (.81 mm).
Install
plug and tighten to 15 ft–lb (20.4 N m). If torque
wrench is not used, tighten plug firmly. Push
wire onto spark plug and reinstall control panel
with (3) capscrews.
1.
2.
Turn ignition key to OFF.
Remove (3) self tapping screws, (2) capscrews,
(1)
washer and (2) nuts securing belt cover to
snowthrower frame (Fig. 13). Set belt cover
aside.
Adjusting Carburetor
The carburetor has been factory set, and no
adjustment is required. However, when operating
snowthrower at altitudes of 5000 feet above sea level
or higher, carburetor jets may have to be changed.
Contact your local Authorized Toro Service Dealer
for assistance.
3.
4.
REMOVING BELT (Fig. 14)—Push down on
idler pulley allowing belt to be removed from
rotor pulley, brake arm assembly, and engine
pulley.
INSTALLING BELT (Fig. 14)—Loop belt
around engine pulley, under idler pulley, over
roller, through brake assembly, and around rotor
pulley.
Replacing Rotor Blades
(Fig. 18-20)
Before each snow season, inspect rotor blades for
wear. When blade edge has worn to the wear indicator
hole (Fig. 18), the blades must be replaced to ensure
proper performance and prevent damage to underside
of snowthrower. Always replace both blades at the
same time.
IMPORTANT: Belt must be on top of roller as
shown.
5.
Reinstall belt cover. Tighten fasteners securely,
but DO NOT OVERTIGHTEN.
9
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38430, Toro 38435, Toro CCR 3000 |
| Model Number | 38430, 38435 |
| Model Year | 1999 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 9900001 - 9999999 |
| Product Name | Toro CCR 3000 38435 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 2000/3000/3600, Single Stage, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Suzuki |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | 47PT7-5 |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(3 votes, average: 3.33 out of 5)
Lawn and Garden readers have rated Toro CCR 3000 GTS 38430 38435 20 Inch Single Stage Snow Blower Operators Manual 1999 3.3 out of 5.0 based on 3 product reviews. I have just downloaded the manual and I have no idea how to access it so I can use it. When I click on the file to open it, It takes me back to the web page so I can download it again. This was my first attempt. Slow learning curve... Hope I can figure out how to use your pages....
I looking for new scrapers for my TORO snow blower model #38430 CCR 3000 GTS 5.0 thanks
If this is the manual for my snowblower, then great site.