Poulan 1950 2025 2050 2075 2150 2175 2350 2375 Chainsaw Owners Manual

SAFETY NOTICE:  Exposure  to vibrations
Location of shipping spacer
through
prolonged
use
of
gasoline
powered  hand  tools  could  cause   blood
vessel  or  nerve   damage  in  the  fingers,
hands,  and   joints   of  people   prone   to
circulation disorders or abnormal swellings.
Prolonged  use in  cold weather  has  been
linked to blood vessel damage in otherwise
healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in the
fingers,  hands,  or joints,  discontinue  the
use of this tool and seek medical attention.
Clamp Nuts
Bar Clamp
An
anti-vibration
system
does
of
not
guarantee
the
avoidance
these
problems. Users  who operate power  tools
on  a  continual   and  regular  basis  must
monitor closely their physical condition and
the condition of this tool.
Assembly Tool
S
An adjusting pin and screw are used to
adjust the tension of the chain. It is very
important when assembling the barthat
the pin located  on the adjusting screw
aligns with a hole in the bar. Turning the
screw will move  the adjustment pin up
anddown the screw. Locate this adjust-
ment  pin before  you begin  mounting
the  bar onto  the saw.  See  illustration
below.
SPECIAL NOTICE:  Your saw is  equipped
with  a  temperature   limiting   muffler  and
spark  arresting  screen  which   meets  the
requirements of California Codes 4442 and
4443.
All U.S. forest land and the states of
California,  Idaho, Maine,  Minnesota,  New
Jersey,  Oregon, and  Washington  require
many  internal combustion   engines to  be
equipped  with a spark  arrestor screen  by
law.  If you operate a chain saw in a state or
locale where such regulations exist, you are
Inside view of
Bar Clamp
legally
responsible   for   maintaining   the
operating condition  of these parts.  Failure
to do so is a violation of the law. Refer to the
SERVICE  section  for  maintenance  of the
Spark Arrestor.
Adjustment screw
S
Turn the adjusting screw counterclock-
wise to  move the adjusting pin  almost
as far as it will go to the rear.This should
allow the pin to be nearthe correct posi-
tion. Further adjustment may be neces-
sary as you mount the bar.
Failure to follow all Safety Rules andPrecau-
tions can result inserious injury. Ifsituations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your Authorized Service
Dealer or call 1-800---554---6723.
S
S
Mount the bar as illustrated.
Slide the bar toward the rear of the saw
as far as possible.
ASSEMBLY
S
Prepare  the   chain  by  checking  the
proper direction. Without  following the
illustration  it is easy to place  the chain
on the saw the wrong direction. Use the
illustration  of the chain to determine the
proper direction.
Theassembly tool provided with your saw is
the only tool  needed for assembly. Protec-
tive gloves  (not provided) should  be worn
during assembly.
S
Place  the chain  onto the  sprocket  lo-
cated behind  the clutch  drum. Fit  the
chain between the teeth in the sprocket.
Start at the top  of the bar and fit chain
into groove around the guide bar.
Pull the  bar forward  until the  chain is
snug in the groove of the bar.
ATTACHING THE BAR & CHAIN (If not
already attached)
S
S
S
WARNING:  Recheck   each  assembly
step if  the saw is  received  assembled. Al-
ways wear gloves when handling the chain.
The chain  is sharp and  can cut you  even
when it is not moving!
Hold guide bar  against the saw frame
and install the bar clamp. Make sure the
adjusting pin is aligned with the hole in
the bar.  Remember this pin moves the
bar forward and backward as the screw
is turned.
S
Loosen andremove the clamp nuts and
the bar clamp from the saw.
Remove the plastic  shipping spacer (if
present).
S
5
Product Specification
CategoriesChainsaw Manuals, Poulan Chainsaw Manuals
Tags, , , , , , ,
Model Year2000
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 13 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website