IGNITION SWITCH
SIDE VIEW
STARTING
ON
WARNING: The chain must not move
when the engine runs at idle speed. If the
chain moves at idle speed refer to CARBURE-
TOR ADJUSTMENT within this manual. Avoid
contact with the muffler. A hot muffler can
cause serious burns.
STOP
CHOKE
(SIDE VIEW)
To stop the engine move the switch to the
STOP or OFF position.
To start the engine hold the saw firmly on
the ground as illustrated. Make sure the
chain is free to turn without contacting any
object.
Choke Knob
OFF
FULL
Use only 15”---18” of rope per pull.
For a warm engine:
Hold saw firmly while pulling starter rope
S
S
Fully push in choke knob.
Move switch to the START or ON posi-
tion.
S
S
Slowly press primer bulb six times.
Squeeze and hold throttle trigger. With
thumb press fast idle lock down; then
release throttle trigger.
S
S
Sharply pull the starter rope with your
right hand until the engine starts.
Squeeze and release throttle trigger to
allow engine to return to idle speed.
Difficult starting or flooded engine:
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ignition
switch is in the ON or START position.
Starting could require pulling the starter
rope handle many times depending onhow
badly the unit is flooded. If engine fails to
start, refer to troubleshooting chart or call
1-800-554-6723.
Important points to remember
When pulling the starter rope, do not use
the full extent of the rope as this can cause
the rope to break. Do not let starter rope
snap back. Hold the handle and let the rope
rewind slowly.
NOTE: Do not attempt to cut material with
the fast idle lock button in the locked posi-
tion.
For
cold engine or warm engine after
running out of fuel:
CUTTING METHODS
S
Move switch to the START or ON posi-
tion.
S
S
S
Pull choke knob out to the full extent.
Slowly press primer bulb six times.
Squeeze and hold throttle trigger. With
thumb press fast idle lock down; then
release throttle trigger.
IMPORTANT POINTS
S
S
S
Cut wood only. Do not cut metal, plas-
tics, masonry,non-wood building mate-
rials, etc.
Stop the saw if the chain strikes a for-
eign object. Inspect the saw and repair
or replace parts as necessary.
S
S
S
Sharply pull the starter rope handle 5
times with your right hand.
Fully push in choke knob; pull the start-
er rope until the engine starts.
Allow the engine to run for approxi-
mately five seconds. Then, squeeze
and release throttle trigger to allow en-
gine to return to idle speed.
Keep the chain out of dirt and sand.
Even a small amount of dirt will quickly
dull achain andthus increase the possi-
bility of kickback.
S
Practice cutting a few small logs using
the following techniques to get the
“feel” of using your saw before you be-
gin a major sawing operation.
Fast idle lock down
S
Squeeze throttle trigger and allow
engine to reach full speed before
cutting.
S
S
Begin cutting with the saw frame
against the log.
Keep the engine at full speed the
entire time you are cutting.
7
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 1950, Poulan 2025, Poulan 2050, Poulan 2075, Poulan 2150, Poulan 2175, Poulan 2350, Poulan 2375 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)