SAFETY NOTICE: Exposure to vibra-
tions through prolonged use of gasoline
powered hand tools could cause blood ves-
sel or nerve damage in the fingers, hands,
and joints of people prone to circulation dis-
orders or abnormal swellings. prolonged use
in cold weather has been linked to blood ves-
sel damage in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss of strength, change in skin color or
texture, or loss of feeling in the fingers,
hands, or joints, discontinue the use of this
tool and seek medical attention. An anti-vi-
Location of shipping spacer
Clamp Nuts
Bar Clamp
bration
system does not guarantee the
Assembly Tool
avoidance of these problems. Users whoop-
erate power tools on a continual and regular
basis must monitor closely their physical
condition and the condition of this tool.
S
An adjusting pin and screw is used to ad-
just the tension of the chain. It is very im-
portant when assembling the bar, that the
pin located on the adjusting screw aligns
into a hole in the bar. Turning the screw
will move the adjustment pin up and down
the screw. Locate this adjustment before
you begin mounting the bar onto the saw.
SPECIAL NOTICE: Yoursaw is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443.
All U.S. forest land and the states of Califor-
nia, Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington require many inter-
nal combustion engines to be equipped with
a spark arrestor screen by law. If you oper-
ate a chain saw in a state or locale where
such regulations exist, you are legally re-
sponsible for maintaining the operating con-
dition of these parts. Failure to do so is a vio-
lation of the law. Refer to the CARE AND
MAINTENANCE section for maintenance of
the Spark Arrestor.
Inside view of
Bar Clamp
Adjustment located on bar clamp
S
Turn the adjusting screw counterclock-
wise to move the adjusting pin almost as
far as it will go to the rear. This should al-
low the pin to be near the correct position.
Further adjustment may be necessary as
you mount the bar.
Mount the bar.
Slide the bartoward the rearof the sawas
far as possible.
Failure
to follow all Safety Rules and
Precautions can result in serious injury If
situations occur which are not covered in this
manual, use care and good judgement. If you
need assistance, contact your Authorized
Service Dealer or call 1-800-554-6723.
S
S
S
Prepare the chain bychecking the proper
direction. Without following the illustra-
tion it is easy to place the chain on the
saw backwards. Use the chain illustra-
tion to determine the proper direction.
Place the chain onto the sprocket located
behind the clutch drum. Fit the chain be-
tween the teeth in the sprocket.
ASSEMBLY
WARNING: If received assembled,
repeat all steps to ensure your unit is proper-
ly assembled and all fasteners are secure.
Always wear gloves when handling
chain. The chain is sharp and can cut you
even when it is not moving!
The assembly tool provided with your saw is
the only tool needed for assembly. Protec-
tive gloves (not provided) should be worn
during assembly.
ATTACHING THE BAR & CHAIN (If
not already attached)
S
the
S
S
S
Start at the top of the bar and fit chain into
groove around the guide bar.
Pull the bar forward until the chain is snug
in the groove of the bar.
Hold guide baragainst the saw frame and
install the bar clamp. Make sure the ad-
justing pin is aligned with the hole in the
bar. Remember this pin moves the bar
forward and backwards as the screw is
turned.
S
Loosen and remove the clamp nuts and
the bar clamp from the saw.
Remove the plastic shipping spacer (if
present).
S
Replace the bar clamp nuts and tighten
finger tight. Once the chain is tensioned
you will need to tighten bar clamp nuts.
S
5
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 2750, Poulan 2775, Poulan 2900, Poulan 3050 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)