Maintenance
Recommended Maintenance Schedule
Service Item
Service Operation
Initial
Annually
Comments
Check and adjust
as needed.
Control cable
Check the control cable. Adjust if necessary.
X
X
Drain the fuel and run the engine until the fuel tank
and the carburetor are dry.
Fuel tank
X
Scraper
Check the scraper. Replace if necessary.
Inspect the drive belt. Replace if necessary.
Clean, inspect, and gap. Replace if necessary.
Inspect the rotor blades. Replace if necessary.
X
X
X
X
Drive belt
Spark plug
Rotor blades
Tighten
fasteners
Check and for loose fasteners and tighten them if
necessary.
Tighten fasteners
as needed.
X
X
CAUTION
POTENTIAL HAZARD
•
If you leave the wire on the spark plug, someone could start the engine.
WHAT CAN HAPPEN
•
Someone accidentally starting the engine could seriously injure you or other bystanders.
HOW TO AVOID THE HAZARD
•
Pull the wire off of the spark plug before you do any maintenance. Also, push it aside so it
does not accidentally contact the spark plug.
Adjusting the Control Cable
C. Unhook the Z fitting from the cable adjuster and
reposition the Z fitting in the top or bottom hole on
the adjuster to obtain a proper gap of 1/16 to 1/8 in.
(0.16 to 0.32 cm) between the control bar bracket
and the handle (Fig. 13).
Periodically check the control cable for proper
adjustment.
1.
2.
Stop the engine and wait for all moving parts to stop.
Move the control bar back toward the handle to
remove the slack in the cable (Fig. 7 or Fig. 8).
3.
Ensure that a 1/16 to 1/8 in. (0.16 to 0.32 cm) gap
exists between the control bar and the handle (Refer to
the inset in Fig. 7). To adjust the cable, go to step 4.
4
3
2
1
897
Figure 13
Note: The control cable must have slack in the
disengaged position.
1.
2.
Spring
3.
4.
Z fitting
Cable
Cable adjuster
4.
Adjust the cable as follows:
D. Install the spring cover over the cable adjuster and
the spring.
Models 38413 and 38419 only:
A. Unhook the spring end from the top hole in the
control bar bracket (Fig. 7).
E. Hook the spring into the top hole of the control bar
bracket (Fig. 7).
B. Slide the spring cover off the spring and the cable
adjuster.
Models 38439, 38440, and 38445 only:
12
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38440, Toro CCR 3650 |
| Model Number | 38440 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 200000001 - 200014063 |
| Product Name | Toro CCR 3650 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 2000/3000/3600, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Toro |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | R-tek |
| Engine Motor Size | 6.5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)