Husqvarna 17 142 Chainsaw Owners Manual

S  Whencuttingwiththesaw,thechainbrake
Place the saw on firm ground. Hold the han-
dles with both hands and apply full throttle.
Activate the chain brake by turning your left
wrist against the hand guard without releas-
ing your grip  around the front  handle. The
chain should stop immediately.
must be disengaged.
Disengaged
Engaged
Inertia activating function control
WARNING:
When performing  the
following  procedure,  the  engine must  be
turned off.
Braking function control
The  chain  brake  must  be
checked  several times  daily.  The  engine
mustberunningwhenperformingthisproce-
dure. This is theonly instancewhen thesaw
should be placed on the ground with the en-
gine running.
Hold the chain  saw approximately 14″   (35
cm) aboveastumporother  woodensurface.
Release your  grip on the front  handle and
use the weight of the saw to let the top of the
guide bar fallforward andcontact thestump.
When the tip of the  bar hits the stump, the
brake should activate.
CAUTION:
CUTTING METHODS
IMPORTANT POINTS
etc. If the tree makes contact with any utility
line, the  utility company should be  notified
immediately.
S  Check chain tension before first use and
after 1 minute of  operation.  See CHAIN
TENSION in the ASSEMBLY section.
S  Cut wood only.  Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S  Stop the saw if the chain strikes a foreign
object. Inspectthesaw  andrepair partsas
necessary.
S  Carefullyplanyour sawingoperationinad-
vance.
S  Cleartheworkarea.  Youneedacleararea
allaroundthetreeso   youcan havesecure
footing.
S  The chain saw operator  should keep on
the uphill side of the terrain as the tree is
likelytorollor  slidedownhillafteritisfelled.
S  Study  the  natural  conditions   that  can
cause the tree to fall in a particular direc-
tion.
S  Keepthechainoutofdirtandsand.    Evena
smallamountofdirtwillquickly    dullachain
and increase the possibility of kickback.
S  Practice cutting a few small logs using the
following techniques to get the“feel” ofus-
ing your  saw before  you begin  a  major
sawing operation.
Natural conditions that can cause a tree  to
fall in a particular direction include:
S  Squeeze the throttle  trigger and  allow
theenginetoreachfullspeedbeforecut-
ting.
S
The wind direction and speed.
S  The lean of the tree.   The lean of  a tree
might not  be apparent due to  uneven or
slopingterrain.  Useaplumb or level tode-
termine the direction of tree lean.
S  Begincuttingwiththesaw  frameagainst
the log.
S  Keep the engine at full speed the entire
time you are cutting.
S
Weight and branches on one side.
S  Surrounding trees and obstacles.
S  Allow the chain to cut for you. Exert only
light downward pressure.
Look for decay and rot. If thetrunk is rotted,
it can  snap and  fall toward  the
operator.
S  Release the throttle trigger as soon as
thecutis  completed,allowingtheengine
to idle.  If you run the saw at full throttle
without  a   cutting  load,  unnecessary
wear canoccur tothechain,bar,anden-
gine.  It is recommended that the en-
gine not be operated for longer than
Check for broken  or dead branches which
can fall on you while cutting.
Make sure there is enough room for the tree
to  fall.   Maintain  a distance  of  2-1/2  tree
lengths from the nearest person or other ob-
jects. Enginenoisecan  drownout awarning
call.
Remove dirt, stones, loose bark, nails, sta-
ples,andwirefromthetreewherecuts    areto
be made.
Plana clear retreat pathto therear anddiag-
onal to the line of fall.
30
seconds at full throttle.
S  To avoid losing control when cut is com-
plete, do not put pressure on saw at end
of cut.
S  Stop the  engine before  setting the  saw
down.
Plan a clear retreat path
TREE FELLING TECHNIQUES
WARNING:
Check  for  broken or
dead branches which  can fall while cutting
causingserious injury. Donotcutnearbuild-
ings or electricalwires ifyou donot know the
directionoftreefall,norcutatnightsinceyou
will not be able to see  well, nor during bad
weather suchas rain, snow,or strongwinds,
Direction of Fall
45
_
10
Product Specification
CategoriesChainsaw Manuals, Husqvarna Chainsaw Manuals
Tags,
Model Year2002, 2003, 2004, 2005
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 18 pages
Document TypeOperator's Manual
LanguageEnglish
Product BrandHusqvarna, Chainsaw
Document File TypePDF
Publisherhusqvarna.com
Wikipedia's PageHusqvarna
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website