Husqvarna 17 142 Chainsaw Owners Manual

ASSEMBLY
Protective gloves (not  provided) should be
6.   Prepare the chain by checking the proper
direction. Without followingthe illustrationit
is easy toplacethechainon  thesaw inthe
wrong direction. Use the illustration of the
chain to determine the proper direction.
worn during assembly.
ATTACHINGTHEBAR&CHAIN   (Ifnot
already attached)
WARNING:  Recheck each assem-
bly stepifthesaw  isreceivedassembled.Al-
ways wear gloves when handling the chain.
The chain  is sharp  and can cut  you even
when it is not moving!
Tip of
Bar
1.
Loosenandremovethechainbrakenuts
and the chain brake from the saw.
Remove the plastic  shipping spacer (if
present).
2.
CUTTERS MUST FACE IN
DIIRECTION OF ROTATION
Location of shipping spacer
Cutters
Depth Gauge
Chain Brake
Nuts
Drive Links
Chain Brake
7.
Place chain over and behind clutch, fit-
ting the  drive links  in the  clutch  drum
sprocket.
Bar Tool
3.
Anadjustingpinandscrew   is usedtoad-
just the tension of the chain. Itis very im-
portant when  assembling the  bar, that
the pin located  on the  adjusting screw
aligns into a hole in the bar. Turning the
screw will  move the adjustment pin  up
and down the screw. Locate this adjust-
ment before you begin mounting the bar
onto the saw. See illustration.
Place chain onto the sprocket
Fit  bottom of  drive  links  between the
teeth in the sprocket in  the nose of the
guide bar.
8.
9.
Fit chain drive links into bar groove.
Inside view of
Chain Brake
10. Pull guide bar forward until chain is snug
in guide  bar groove.   Ensure  all drive
links are in the bar groove.
11.
Now, install chain brake making surethe
adjusting pin is  positioned in the  lower
hole inthe guidebar.  Remember this pin
moves the bar forward and backward as
the screw is turned.
Adjustment located on Chain Brake
4.
5.
Turn the adjusting screw by hand coun-
terclockwise until the  adjusting pin just
touches the stop.  This should allow the
pin to be near the correct position. Fur-
ther adjustment  may be  necessary as
you mount the bar.
Slide guide bar behind clutch drum until
guide  bar  stops  against  clutch  drum
sprocket.
12.
Installchainbrakenutsandfingertighten
only.  Once the chain is tensioned, you
will need to tighten chain brake nuts.
CHAIN TENSION
(Including units with chain already installed)
NOTE:    When  adjusting  chain  tension,
make sure the chain  brake nuts are finger
tight only.   Attempting to tension the  chain
when  the chain  brake  nuts are  tight  can
cause damage.
Checking the tension:
Use the screwdriver  end of the bar  tool to
move the chain around the bar. If the chain
does notrotate,itis  tootight.Iftooloose,    the
chain will sag below the bar.
Mount the Bar
7
Product Specification
CategoriesChainsaw Manuals, Husqvarna Chainsaw Manuals
Tags,
Model Year2002, 2003, 2004, 2005
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 18 pages
Document TypeOperator's Manual
LanguageEnglish
Product BrandHusqvarna, Chainsaw
Document File TypePDF
Publisherhusqvarna.com
Wikipedia's PageHusqvarna
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website