NOTE: If the throttle trigger is squeezed
during starting, it will be necessary to reset
the fast idle lock.
When cutting with the saw,the chain brake
must be disengaged.
S
Disengaged
Engaged
S Pull the starter rope quickly with your right
hand a maximum of 10 times. Then, pro-
ceed to the next step.
NOTE: If the engine sounds as if it is trying
to start before the 10th pull, stop pulling and
immediately proceed to the next step.
S Push the choke/fast idle lever in complete-
ly (to the OFF CHOKE position).
Braking function control
CAUTION:
S Pull the starter rope quickly with your right
hand until the engine starts.
The chain brake must be
checked several times daily. The engine
must be running when performing this proce-
dure. This is the only instance when the saw
should be placed on the ground with the en-
gine running.
S Allow the engine to run for approximately 5
seconds. Then, squeeze and release the
throttle trigger to allow engine to return to
idle speed.
STARTING A WARM ENGINE
Place the saw on firm ground. Grip the rear
handle with your right hand and the front han-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
S Move ON/STOP switch to the ONposition.
S Press the throttle lock with your right hand.
Squeeze and hold the throttle trigger;
Press and hold the fast idle lock with your
forefinger; release the throttle trigger.
S Be sure choke/fast idle lever is in the OFF
CHOKE position.
S Pull the starter rope quickly with your right
hand until the engine starts.
Inertia activating function control
S Squeeze and release the throttle trigger to
allow engine to return to idle speed.
WARNING: When performing the
following procedure, the engine must be
turned off.
DIFFICULT STARTING (or starting a
flooded engine)
Grip the rear handle with your right hand and
the front handle with your left hand. Hold the
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ON/
STOP switch is in the ON position.
chain saw approximately 14 (35 cm) above
!
a stump or other wooden surface. Release
your grip on the front handle and use the
weight of the saw to let the top of the guide
bar fall forward and contact the stump.
When the tip of the bar hits the stump, the
brake should activate.
Starting could require pulling the starter rope
handle many times depending on how badly
the unit is flooded. If engine fails to start refer
to the TROUBLESHOOTING TABLE or call
1--800--554--6723.
CUTTING METHODS
CHAIN BRAKE
IMPORTANT POINTS
S
Check chain tension before first use and
WARNING: If the brake band is worn
too thin it may break when the chain brake is
triggered. With a broken brake band, the
chain brake will not stop the chain. The chain
brake should be replaced by an authorized
service dealer if any part is worn to less than
after 1 minute of operation. See CHAIN
TENSION in the ASSEMBLY section.
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair parts as
necessary.
0.020
! (0.5 mm) thick. Repairs on a chain
brake should be made by an authorized ser-
vice dealer. Take your unit to the place of pur-
chase if purchased from a servicing dealer,
or to the nearest authorized master service
dealer.
S Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull a chain
and increase the possibility of kickback.
S Practice cutting a few small logs using the
following techniques to get the “feel” of us-
ing your saw before you begin a major
sawing operation.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S Squeeze the throttle trigger and allow
the engine to reach full speed before
cutting.
S The
inertia--activated
chain brake is
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is
disengaged by pulling the front hand guard
back toward the front handle as far as
possible.
S Begin
cutting with the saw frame
against the log.
S Keep the engine at full speed the entire
time you are cutting.
S Allow the chain to cut for you. Exert only
light downward pressure.
10
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 3450, Poulan 3750 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)