Outlet Cover
S Clean the oil holes and bar groove after
Exhaust
Outlet
each 5 hours of operation.
Remove Sawdust From
Guide Bar Groove
Exhaust Outlet must face chain
brake (bar side) of chain saw
Oil Holes
10.
11.
Inspect the muffler gasket and replace if
damaged.
S Burring of guide bar rails is a normal
process of rail wear. Remove these burrs
with a flat file.
Reinstall backplate,outlet guide,muffler
gasket, and muffler using muffler bolts.
Tighten until secure.
S Whenrailtopis uneven,useaflatfiletore-
12.
Reinstallboltcover andlocknut. Tighten
securely.
store square edges and sides.
File Rail Edges
and Sides
Square
CARBURETOR ADJUSTMENT
WARNING:
The chain will be mov-
ing during mostof this procedure. Wear your
protective equipment and observe all safety
precautions.Thechainmustnotmoveatidle
speed.
Worn Groove
Correct Groove
Replace guide bar when the groove is worn,
theguidebar is bentor cracked,or whenexce-
ss heating or burring of the rails occurs. If re-
placementis necessary,useonlytheguidebar
specified for your saw in the repair parts list or
on the decal located on the chain saw.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if
you notice any of the following conditions:
S Chain moves at idle. See IDLE SPEED--T
adjusting procedure.
CHAIN SHARPENING
S Saw will not idle. See IDLE SPEED--T ad-
justing procedure.
Idle Speed--T
Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpening to a professional
chain sharpener.
Allow engine to idle. If the chain moves, idle
istoofast. Iftheenginestalls,idleis tooslow.
Adjust speed until engine runs without chain
movement (idle too fast) or stalling (idle too
slow). Theidle speedscrew is located inthe
area above the primer bulb and is labeled T.
S Turn idle speed screw (T) clockwise to in-
crease engine speed.
IGNITION TIMING
Ignition timing is fixed and nonadjustable.
SPARK PLUG
The spark plug should be replaced each
year to ensure the engine starts easier and
runs better.
S Turn idle speed screw (T) counterclock-
wise to decrease engine speed.
1.
2.
3.
4.
Loosen 3 screws on cylinder cover.
Remove the cylinder cover.
If you require further assistance or are unsure
about performing this procedure, contact your
call
Pull off the spark plug boot.
Remove spark plug from cylinder and
discard.
authorized
service
dealer
or
1--800--554--6723.
5.
Replace with Champion RCJ--7Y spark
plug and tighten securely with a 3/4 inch
BAR MAINTENANCE
(19
mm) socket wrench. Spark pluggap
If your saw cuts to oneside, has to beforced
throughthecut,or beenrunwithanimproper
amount of bar lubrication it may be neces-
sarytoserviceyourbar. A wornbar willdam-
age your chain and make cutting difficult.
After each use, ensure ON/STOP switch is
in the STOP position, then clean all sawdust
from the guide bar and sprocket hole.
To maintain guide bar:
should be 0.025 inch (0.6 mm).
Reinstall the spark plug boot.
6.
7.
Reinstall
screws. Tighten securely.
Screws
the
cylinder
cover
and 3
Cylinder
Cover
Spark
Plug Boot
S Move ON/STOP switch to the STOP posi-
tion.
S Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from
saw.
Spark
Plug
15
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 1950, Poulan 1975, Poulan 2050, Poulan 2055, Poulan 2075, Poulan 2150, Poulan 2150PR, Poulan 2155, Poulan 2175, Poulan 2350, Poulan 2375, Poulan LE-Series |
| Model Year | 2003 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)