damage
in
otherwise
healthy
people.
If
Location of shipping spacer
symptoms occur such as numbness, pain,
loss ofstrength,changeinskincolor ortexture,
or loss offeeling inthe fingers,hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely
their
physical
condition
and
the
Chain Brake
Nuts
condition of this tool.
SPECIALNOTICE:Yoursaw isequipped
Chain Brake
with a temperature limiting muffler andspark
the
arresting
screen
which
meets
requirements of California Codes 4442 and
4443.
All U.S. forest land and the states of
Bar Tool
3. An adjusting pin and screw is used to ad-
just the tension of the chain. It is very im-
portant when assembling the bar, that the
pin located on the adjusting screw aligns
intoaholein thebar. Turningthe screw will
move the adjustment pin up and down the
screw. Locate this adjustment before you
begin mounting the bar onto the saw. See
illustration below.
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines
tobeequippedwithaspark arrestingscreen.
Ifyouoperateachainsaw inastate or locale
wheresuchregulations exist,you arelegally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
section
arresting screen.
for maintenance of the spark
Inside view of
Chain Brake
FailuretofollowallSafetyRules andPrecau-
tions canresult inserious injury. Ifsituations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your authorized service
dealer or call 1-800--554--6723.
Adjustment located on Chain Brake
STANDARDS: This saw is listedbyUnder-
writer’s Laboratories, Inc., and the Canadian
Standards Association in accordance with:
4.
Turn the adjusting screw by hand coun-
terclockwise until the adjusting pin just
touches the stop. This should allow the
pin to be near the correct position.
Slide guide bar behind clutch drum until
guide bar stops against clutch drum
sprocket.
ANSI B175.1-2000
American National
Standard for Powered Tools -- Gasoline
Powered Chain Saw -- Safety Requirements
CSA Z62.1--03 Chain Saws -- Occupational
Health and Safety
5.
CSA Z62.3--96 Chain Saw Kickback Occu-
pational Health and Safety
ASSEMBLY
Mount the Bar
Carefully remove the chain from the pack-
age. Hold chain with the drive links as
shown.
Protective gloves (not provided) should be
worn during assembly.
ATTACHINGTHEBAR&CHAIN (Ifnot
already attached)
6.
Tip of
Bar
WARNING:
If received assembled,
repeat all steps to ensure your saw is properly
assembled and all fasteners are secure. Al-
ways wear gloves when handling the chain.
Thechainis sharp andcan cutyou evenwhen
it is not moving!
1.
Loosenandremovethechainbrakenuts
and the chain brake from the saw.
Remove the plastic shipping spacer (if
present).
CUTTERS MUST FACE IN
DIIRECTION OF ROTATION
2.
6
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 2550T |
| Model Year | 2004 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)