MAINTENANCE
V-BELTS
TO CHANGE ENGINE OIL
Check V-belts for deterioration and wear after every 50
hours of operation and replace if necessary. The belts
are not adjustable. Replace belts if they begin to slip from
wear. (See “TO REMOVE BELT COVER” in the Service
and Adjustments section of this manual).
Determine temperature range anticipated before next oil
change.AlloilmustmeetAPIservice classificationSG–SL.
•
•
•
Be sure snow thrower is on level surface.
Oil will drain more freely when warm.
Catch oil in a suitable container.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Using other
than OEM belts can cause personal injury or damage to
the snow thrower.
NOTE: The left side wheel may be removed from snow
thrower for easier access to the oil drain plug and place-
ment of a suitable container.The unit tilted, resting on the
frame with the left wheel removed, will help drain any oil
trapped inside the engine. (See “TO REMOVE WHEELS”
in the Service and Adjustments section of this manual).
AUGER GEAR CASE
•
The gear case was filled with lubricant to the proper
level at the factory. The only time the lubricant needs
attention is if service has been performed on the gear
case.
1.
Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2. Clean area around drain plug.
•
If lubricant is required, use only Ronex ED #1 grease.
3. Remove drain plug and drain oil in a suitable container.
4. Install drain plug and tighten securely.
TRACTION DRIVE SYSTEM
DO NOT lubricate the drive components inside the snow
thrower. The sprockets, hex shafts, drive disc and friction
wheel require no lubrication. The bearings and bushings
are lifetime lubricated and require no maintenance.
5. Wipe off any spilled oil from snow thrower and engine.
6.
Install left wheel (if removed for draining oil).Be sure to
install klick pin into proper hole in wheel axle (See “TO
REMOVE WHEELS” in the Service and Adjustments
section of this manual).
CAUTION:Anylubricatingoftheabovecompo-
nents can cause contamination of the friction
wheel and damage to the drive system of your
snow thrower.
7.
8.
Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine.
Refill engine with oil through oil dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCTSPECIFICATIONS”sectionofthismanual.
ENGINE
See engine manual.
9.
Use gauge on oil fill cap/dipstick for checking level. Be
sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
LUBRICATION
10.
Wipe off any spilled oil.
Use only high quality detergent oil rated with API service
classification SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
SPARK PLUG
Replacesparkplugatthebeginningofeachseasonorafter
every100hoursofoperation,whicheveroccursfirst. Spark
plug type and gap setting are shown in the “PRODUCT
SPECIFICATIONS” section of this manual.
CLEANING
IMPORTANT: For best performance, keep snow thrower
housing free of any dirt or trash. Clean the outside of your
snow thrower after each use.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
WARNING: Disconnectsparkplugwire
from spark plug and place wire where it
cannot come in contact with plug.
32°F.
Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
Change the oil after every 50 hours of operation or at least
once a year if the snow thrower is not used for 50 hours
in one year.
•
•
Keepfinishedsurfaces/wheelsfreeofgasoline,oil,etc.
We do not recommend using a garden hose to clean
yoursnowthrowerunlesstheelectrical system,muffler
and carburetor are covered to keep water out. Water
in engine can result in shortened engine life.
Checkthecrankcaseoillevelbeforestartingtheengineand
after each five (5) hours of continuous use. Tighten oil fill
cap / dipstick securely each time you check the oil level.
15
| Categories | Poulan Pro Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Poulan Pro PP524B |
| Model Year | 2004 |
| Download File |
|
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)