Computed kickback angle (CKA) Table
BAR
MODEL
MC3516
P/N
Length
CHAIN P/N CKA without chain brake
530051544
33_
530044692
16″
NOTE:
If this saw is to be used for com-
SPECIALNOTICE:Yoursaw isequipped
mercial logging, a chain brake is required
and shall not be removed or otherwise dis-
abled tocomply withFederal OSHA Regula-
tions for Commercial Logging.
with a temperature limiting muffler andspark
arresting
screen
which
meets
the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines
tobeequippedwithaspark arrestingscreen.
Ifyouoperateachainsaw inastate or locale
wheresuchregulations exist,you arelegally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
WARNING:
The engine exhaust
from this product contains chemicals known
to the State of California to cause cancer,
birth defects or other reproductive harm.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
section
for
maintenance
of
the
spark
people
prone to circulation disorders or
arresting screen.
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
Failure
to
follow
all
Safety
Rules
and
Precautions can result in serious injury. If
situations occur which are not covered in this
manual, use care and good judgement. If you
need assistance, contact your authorized
service dealer or call 1-800--554--6723.
damage
in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss ofstrength,changeinskincolor ortexture,
or loss offeeling inthe fingers,hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
STANDARDS: This saw is listed by Under-
writer’s Laboratories, Inc., in accordance with:
B175.1--2000 American National
for Gasoline--Powered Chain
ANSI
Standards
closely
condition of this tool.
their
physical
condition
and
the
Saws -- Safety Requirements
CSA Z62.1--03 Chain Saws -- Occupational
Health and Safety
CSA Z62.3--04 Chain Saw Kickback Occu-
pational Health and Safety
ASSEMBLY
Protective gloves (not provided) should be
worn during assembly.
ATTACHINGTHEBAR&CHAIN (Ifnot
already attached)
WARNING:
If received assembled,
Clutch cover
Bar nuts
repeat all steps to ensure your saw is properly
assembled and all fasteners are secure. Al-
ways wear gloves when handling the chain.
Thechainis sharp andcan cutyou evenwhen
it is not moving!
Location of
shipping
spacer
1.
Loosenandremovethebar nuts andthe
clutch cover from the saw.
Remove the plastic shipping spacer (if
present).
2.
Chain adjustment tool
(Bar Tool)
3.
An adjusting pin and screw is used to ad-
just the tension of the chain. It is very im-
portant when assembling the bar, that the
pin located on the adjusting screw aligns
intoaholeinthebar.Turningthescrewwill
move the adjustment pin up and down the
screw. Locate this adjustment before you
begin mounting the bar onto the saw. See
following illustration.
6
| Categories | Chainsaw Manuals, McCulloch Chainsaw Manuals |
|---|---|
| Tags | McCulloch MC3516 |
| Model Year | 2005, 2006, 2007, 2008, 2009, 2010 |
| Download File |
|
| Language | English |
| Product Brand | McCulloch. Support Phone for US: Wheeled (Mowers, Tractors, Tillers, Snow Throwers) - 1-800-849-1297
McCulloch Handheld (Chainsaws, Trimmers, Blowers, Edgers) - 1-800-554-6723 All McCulloch Products - 1-800-521-8559, Chainsaw |
| Document File Type | |
| Publisher | mcculloch.com |
| Wikipedia's Page | McCulloch Motors |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)