1.
2.
3.
Move ON/STOP switch to the ON posi-
tion.
Pullthechoke/fastidlelever outtothefull
extent (to the FULL CHOKE position).
Pull starter rope quickly with your right
handamaximumof10times. Then,pro-
ceed to the next step.
CHAIN BRAKE
WARNING: Ifthebrakebandisworn
too thin it may break when the chain brake is
triggered. With a broken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by an authorized service
dealer if any part is worn to less than 0.020″
(0.5 mm) thick. Repairs on a chain brake
shouldbemadeby anauthorizedservicedeal-
er. Take your unit to the place of purchase if
purchased from a servicing dealer, or to the
nearest authorized master service dealer.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
NOTE: If the engine sounds as if it is trying
to start before the 10th pull, stop pulling and
immediately proceed to the next step.
4.
5.
6.
Push the choke/fast idle lever in to the
HALF CHOKE position.
Pull the starter rope quickly with your
right hand until the engine starts.
Allow theenginetorunfor approximately
30
seconds. Then, squeeze and release
S The
inertia--activated chain brake is
throttletrigger toallow engineto returnto
idle speed.
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is
disengagedby pullingthefronthandguard
back toward the front handle as far as
possible.
ON/STOP SWITCH
S Whencuttingwiththesaw,thechainbrake
must be disengaged.
Disengaged
Engaged
CHOKE/FAST IDLE LEVER
FULL
HALF
OFF
Braking function control
The chain brake must be
CAUTION:
checked several times daily. The engine must
be running when performing this procedure.
This is the only instance when the saw should
be placed on the ground with the engine run-
ning.
STARTING A WARM ENGINE
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
1.
2.
MoveON/STOP switchtotheONposition.
Pull the choke/fast idle lever out to the
HALF CHOKE position.
3.
4.
Pull the starter rope quickly with your right
hand until the engine starts.
Squeeze and release the throttle trigger
to allow engine to return to idle speed.
Inertia activating function control
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded if it has not started
after 10 pulls.
WARNING:
When performing the
following procedure, the engine must be
turned off.
Grip therear handlewith your right handand
the front handle with your left hand. Holdthe
chain saw approximately 14” (35 cm) above
a stump or other wooden surface. Release
your grip on the front handle and use the
weight of the saw to let the top of the guide
bar fall forward and contact the stump.
When the tip of the bar hits the stump, the
brake should activate.
Floodedengines canbe clearedof excess fuel
by following the warm engine starting proce-
dure listed above. Ensure the ON/STOP
switch is in the ON position.
Startingcouldrequiremanypulls dependingon
how badly unit is flooded. If engine still fails to
start, refer to TROUBLESHOOTING TABLE
or call 1-800-554-6723.
10
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 2750, Poulan 2775, Poulan 2900, Poulan 3050 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)